American Standard 2860.334 Enfield Two Piece Toilet - Page 4 - Answered Questions & Fixed issues
Air switch
Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.
Search for TBS-339 Air Switch
US Parts Center
5/25/2014 5:34:40 PM •
American...
•
Answered
on May 25, 2014
•
262 views
Whirpool bath starts when I press button but stops as soon as I release button
Hi Joey, The problem is likely that the switch is installed incorrectly. I'm sorry I don't recommend or advise any repair of a appliance that is water/electrical by anyone other than an authorized repair person. Furthermore, I would not use the appliance again until you have have professional repairs done.
5/20/2014 9:02:38 PM •
American...
•
Answered
on May 20, 2014
•
56 views
Tub will not turn off
If your pump will not shut off when you push the button on the tub then you have a bad air switch in the motor.
Rod
US Parts Center
5/1/2014 2:20:44 PM •
American...
•
Answered
on May 01, 2014
•
58 views
Hydromassage 1063
Not normal for that to happen but the jet faces on the two back jets may be turned off or down.
Try turning the face of the jet clockwise and see if you get more water flow out of each jet.
Rod
US Parts Center
4/13/2014 11:19:33 PM •
American...
•
Answered
on Apr 13, 2014
•
926 views
Pump runs normally with no water but surges when filled with water
When there is a load on the motor and it is surging this is an indication of not enough water getting to the front of the pump.
Check the water flowing inside the tub going from the jet opposite the suction cover.
Sounds to me like you may be getting cavitation because the pump is pulling in too many air bubbles from the jet.
Close the air control and/or move the direction of the eyeball from pointing at the suction cover and see if that helps.
Rod
US Parts Center
4/9/2014 8:44:46 PM •
American...
•
Answered
on Apr 09, 2014
•
102 views
Down stair toilet bubbles when upstair toilet is flushed. never had this problem with old toilet
The roof vent for the toilets is shared. It is the pipe (on the roof) that lets water in the drain system. When clogged, it causes what you have. A garden hose placed in the roof vent (and turned on) may clear the blockage (could be leafs or pine straw or a dead bird). Needs to be cleared... I have used a plumbers snake with 100% success....but you may not have one...so the garden hose suggestion. Be careful on the roof.
3/11/2014 3:50:29 AM •
American...
•
Answered
on Mar 11, 2014
•
135 views
I have a jetted tub and it won't turn off. I have a single button in the back right corner and i don't know what to do!
Right now you are having to turn it on/off by using the circuit breaker or just unplugging the pump right?
Is this a button you depress or an electric button like you would find on a microwave?
If it is a button you depress to turn it on/off then the problem is most likely the air switch located in the motor under the skirt of the tub.
If it is an electric button then it may be the control box under the tub that needs to be replaced.
Rod
US Parts Center
888-521-6183
2/26/2014 11:24:57 PM •
American...
•
Answered
on Feb 26, 2014
•
336 views
We have 3 toilets in the house. the tanks won't refill after flushing
You may have dirt getting into your water from the well and clogging the fill valves in your toilets. Valve assembly can be opened and cleaned out from the top. Instructions are available on AS website for your model. (Note) If you are picking up material from your well, a sediment filter should be added to your water line.
2/1/2014 1:30:37 PM •
American...
•
Answered
on Feb 01, 2014
•
104 views
Water wont stop running
Water is either running (1) into the overflow tube or (2) out to the toilet under the flapper at the bottom of the tank. If (1) lower the ball or float. Done differently depending on model. If (2) replace the flapper with new flapper designed for your model. (Note: Raise manually the float valve and if water still runs out the little tube that goes into the overflow tube then fill valve is defective. Replace it.)
2/1/2014 1:12:36 PM •
American...
•
Answered
on Feb 01, 2014
•
157 views
How to unfreeze toilet pipes in a mobile home
I live in a mobile home park and that is what i do as the park handyman. The fastest way... cut the pipe with a recipricating saw and remove a long section. Knock it to let all the ice slide out. bring it into a warm shop for a while if you have to or run warm water through it. place a micro furnace near the sewer and use a heatgun if more ice is at the other end. Once things are clear, use two 3 inch fernco adapters and clamp everything back together. (i always keep a couple on hand just in case this happens) Make sure the lean is perfectly angled with no place for water to sit or this is what happens.
11/30/2013 6:14:08 AM •
American...
•
Answered
on Nov 30, 2013
•
131 views
Air switch doesn't return to top position
follow this steps and fix it. God bless you
Clear a blocked water intake:
- Twist-off or unscrew the intake cover.
- Clean the intake cover with an old toothbrush and powdered laundry detergent. Rinse any soap residue from the cover before reinstalling.
- Replace the cover.
Replace a jet:
- Identify the damaged or inoperative jet and make sure it requires replacement.
- Follow the owner's manual instructions for removing the old jet. Some twist out by hand while others require a special wrench.
- Find an exact replacement jet (through a pool or spa supplier) and install the new jet.
11/24/2013 1:07:22 PM •
American...
•
Answered
on Nov 24, 2013
•
92 views
I have a American Standard Corner Whirlpool Year
t sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.
US Parts Center
11/15/2013 5:05:38 PM •
American...
•
Answered
on Nov 15, 2013
•
425 views
Bad control switch
What is the problem? How do you turn this tub on/off ?
11/15/2013 4:05:55 PM •
American...
•
Answered
on Nov 15, 2013
•
52 views
Toilet keeps running
Bad flapper valve or water level is above overflow tube. Replace flapper or lower float.
11/11/2013 11:52:59 PM •
American...
•
Answered
on Nov 11, 2013
•
95 views
Not finding what you are looking for?