American Standard 4112.016 Cadet Toilet Tank w/Coupling Components & Tank T - Page 5 - Answered Questions & Fixed issues

Flapper seal is damaged or worn out. Replace Flapper with one for your model.

It could be a venting issue. Check the roof vent for the plumbing system. Perhaps clogged with leaves or other debris causing a blockage in the vent line. You can use a hose up to the roof and flush out the vent line. Another problem may be calcium buildup. CLR , a product available at most hardware and grocery stores will dissolve mineral buildups.

Try a bathroom supply shop or your place of purchase. Failing that try http://www.americanstandard-us.com/support/

If you've tried turning off both shutoffs underneath and water still runs, then the shutoffs are also likely worn out and need to be replaced. If there is no way to shut off from that point, then the only other option is to have somebody turn off all water in the house near your water meter or main water line. In many places, hardware stores will sell something called a "water shutoff key", but depending on your location, it may have a different local name. Once water is off to the whole house, turn the hot water on somewhere in the house to reduce pressure from your water heater before replacing your faucet and shutoff valves. It is a good idea to take one of your old water shutoffs with you to a hardware store to make sure the new one would fit propperly. If you know somebody who can take apart the faucets to check and replace just the washers, then it could be fixed with even less expense, if you would not rather replace the faucet with a new one that will last longer.

This sounds like the air switch in the motor is not working properly. You will need to remove the pump from under the tub to access the air switch located in a housing on the motor.

Replacement Air Switch will cost you about $20US Parts Center

Two things come to mind, The sinks were installed out of balance and way over tightened causing a constant stress on a warped surface, or a foreign object was left under lips of sinks. If they were purchased and installed at the same time you could have received damaged merchandise.

You may have to use a really neat tool and that is aunt splitter. You can get it at O Reilly's auto store or any of those stores. That should remove it.

There is a clog in the line. A plunger usually solves this problem, but you have to use a toilet plunger. Your local hardware store will give you the right tool ($13). If the plunger doesn't work, you need a toilet auger (also called a closet auger), which you can buy for less than $20.

replace float assembly

The brown ring is usually caused by hard water stains. With bit of chemicals scrubbed with a scouring stick. Toilets are fairly cheap if you need a new one for better looks.

most likely the chain that comes from the handle is holding the stopper.so just give the chain a little slack.

Shut the water off flush toilet and there should be two bolts that you can see at the under side of that tank. You need to remove them bolts and lift off the tank and install a new seal. Sometimes i mean sometimes you can tighten them a little and they will stop leaking. If it has been for awhile id just replace it. I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_a3369546f8067589

Check the aerators for debris. Aerators are located at the end of the spout where the water comes out. Usually these unscrew counterclockwise (some models require a tool). Rinse out and reinstall. They may be just a lower flow model.

I haven't sat on your toilet, so the rockin' don't come from me! Our grandpa had a habit of slamming his a@@ down on the toilet here at my house, so now it rocks when sat on. The bolts have shifted, or the wax ring was smisshed. If you take off the toilet from the floor, and find out either/or, let me know.

I seen two tpyes one where the inter jet unscrew and the other where the outter ring unscrews not sure what kind you have . Went to the pool store and they had a cleaner you add to the water and then run the unit for about 20 minutes then drain . It seem to work pretty good and there was less hassel taking the jets apart

0If you mean first, it is tenths. (or .7)

I have one. Call me at 510 559 0623.

Configure

Hi delen zxi...
Replace your flapper valve as it is faulty and causing your leakage and refilling problem...
See the following YouTube video to explain how to install a new flapper vave..
Please take time to rate me thumbs up

http://www.askthebuilder.com/Toilet_Flapper_Valve_Video.shtml

There is a plastic cap that you need to flip open. You can do this by prying the flap at the top of the hinge. Once you pop it open you will need a screw driver to turn the screw that is inside/underneath the hinges. Turn the screw clockwise until it is good and snug. then snap the hinge cap back into place by applying pressure to it.