20 Most Recent
KitchenAid KSM150PS Artisan Series Stand Mixer - Page 2 Questions & Answers
I have a ksm150psbu my
The head height adjustment screw is visible from the front when the head is raised. Looking from the front it is right at the back where the machine head hinges on thew pedestal. Clockwise to lower and anti clockwise to raise the head. You want it as low as possible without the flat paddle tinging on the bowl when the motor is running. Kitchen aid also make a paddle with rubber edges, called a scraper paddle. That one wipes against the bowl during operation.
Kitchen aid mixer repair locationsi
Leaking oil is caused by the grease in the gear box separating. This often happens when the mixer is not used much and the grease is not kept mixed by the moving gears. The solution is two-fold. First run the machine more frequently. Second is to open the head and replace the old grease with an approved food-grade grease (6 oz. is the right amount). KitchenAid grease can be found online and at Ebay. The Service Manual can be found at:
http://www.kitchenaidparts.eu/documents/pdf/service-manual/classic-svc-manual-new-email-version.pdf
While the Artisan series is not specifically referenced, the procedures are the same.
You can also take the mixer and manual to a competent repair person.
How do I reattach the motor wire to the brush holder insert? Do I lube the new motor?
On one brush holder you push the clip on the end of the field wire between the bottom side of the square brush holder and the black plastic insert the holder is mounted into. On the other brush holder it pushes between the top side of the brass holder and the black insert. The bearing is pre lubricated but oil the armature shaft before sliding the rear bearing housing on.
Kitchen aid stand mixer bought in US, moving to Europe, 220v 50hz
I can not respond to the warranty issues. My kitchen aid mixer is past warranty as well. I live in a country that uses 220V and my kitchen aid mixer is 110V. I have been using my kitchen aid mixer for almost 4 years with no problems at all.
The converter boxes are supposed to blow the fuse on the converter before it reaches your appliance and cause any problems.
If you purchase a 220V kitchen aid (although it would cost more money) it would probably have more power because of the higher voltage.
Hope this helps!
My artesian kitchenAid stand mixer will not turn back on after using it
Make sure it's unplugged, remove and inspect the carbon brushes one at a time under those black screws on the side. They are keyed with one corner of the square ground off so will only go in properly one way so eyes open when you take them out. If they are less than 10mm long replace them. Next would be look under the back cover for a broken wire to the black square speed control plate. Broken wires are only likely to be one of the bottom 2 on either side. Any more testing is going to require a multimeter.
How do I get my mixer to turn on?
Occasionally the wire that goes to the carbon brush holder from the fields can pop out and no longer connect to the holder. You need to do your testing with a multi meter as anything more than what you have done is going to require splitting the gear cases to fix. There is sometimes a small pcb between the mains input and the speed control, that's between the cases screwed to the bottom part at the back.
In the middle of making my cookies the mixer turned off and wont come on again
Make sure it's unplugged, remove and inspect the carbon brushes one at a time under those black screws on the side. They are keyed with one corner of the square ground off so will only go in properly one way so eyes open when you take them out. If they are less than 10mm long replace them. Next would be look under the back cover for a broken wire to the black square speed control plate. Broken wires are only likely to be one of the bottom 2 on either side. Any more testing is going to require a multimeter.
What is the rpm of artisan 300watts
On low speed roughly 1 rotation of the planetary per second. On high speed it should be the maximum speed that motor can run at, too fast to count that's for sure.
Kiitchenaid artisan head will tilt but wont stay up
On the same side as the head lock lever at the back of the pedestal there is normally a small plastic part that the locking lever can hook under. It is held on by a single pop rivet. Maybe it has broken off. In the back of my mind I thought those things tipped back far enough that they were beyond the balance point and didn't want to fall back down anyway. Are you sure it is tipping all the way back?
Not finding what you are looking for?