Top 20 KitchenAid KEMC377K Convection / Microwave Oven - Page 4 Questions & Answers

Get rid of it and buy a new one. This sounds like a dangerous item to continue to use. ...

Go to Kitchenaid's web site and see if you can order replacement accessories. If not, try contacting their support group. Usually, if you search for: Make Model replacement parts you will find web sites that carry the item you seek. ..

The door handles on most appliances, like outside cars & truck handles, are secured with screws from inside the door. You will need to take the door completely apart to tighten the screws. This may be a very hard job, as it needs to be reassembled as well. God bless your efforts.

It may be what I call the "overdesigned door circuit," as shown in the attached drawing. If you'd like more help with this, I'd need your full model number and FCC ID number form the tag in the cooking cavity or elsewhere on the oven. Feel free to contact me via microwavecontrol.com with your detailed symptoms.

Erratic behavior sometimes occurs when microwaves are not plugged into grounded outlets. Make sure it is actually grounded. If so, you might have a defective control panel. If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_29ad5d1dd86564b0

If you wish to get some details about microwave oven repair then check the following link http://electro-medical.blogspot.com/

If you wish to get some details about microwave oven repair and error codes then check the following link http://electro-medical.blogspot.com/

Search Results

Combination Microwave Wall Oven - Error Code/Message ...

www.kitchenaid.com/...microwave...error-code...f6-error-cod...
KitchenAidQuestion: Combination Microwave Wall Oven - Error Code/Message - F6 Error Code -F6 E8. Answer. Product Symptom: Combination Microwave Wall Oven ...

Over-the-Range Microwave - Error Code - Starts with F ...

www.kitchenaid.com/...microwave-error-code...f...f6...code/P...
KitchenAidKitchenAid's product help articles give answers to your frequently asked questions (FAQs). ... Microwave - Error Code - Starts with F - Starts with F6 - F6E0 Code.

Kitchen Aid Oven Model # KEMS308SSS02 error msg - Lost ...

www.shopyourway.com > Manage My Life > Questions
I have a Kitchen Aid Model # KEMS308SSS02 and I getting the follow error message... is working and was always working but the top microwave/oven does not work. ...Kitchen Aid Oven Model # KEMS308SSS02 error msg - Lost Err/ F6 E0/ ... Most "F6/E0" fault codes is usually because of a loose wire connections, loss of ...

Sarah, That model number is not coming up as a good number, but another model that I looked at said that particular model was a 900 watt microwave.

some circuit problem

check manual and do

You must presume Tech knows what he is talking about , but get 2nd opinion, then you will be sure.

Door Latch might be defective.

can you say,,,buy a new one???

It sounds to me that your door switches aren't working.Your oven is protected by a couple of switches that engage when you open or close the door.They control a couple of safety features and also your interior light.One of them seems defective.

on my microwave, the door sticks some times & I put my fingers under door on latch side & push up, & I can hear it release & open. other than that there may be a broken part. follow the link below. KitchenAid Microwave Door Won Open

When unplugging it for half a minute or so (this should reset all settings) won't help, it must be defect. When you are convinced you did press the right buttons and you are in the correct program you don't need to unplug. But for that you have to be sure it is not switched to oven. In 30 seconds it won't be warm enough to heat your coffee

http://kitchen.manualsonline.com/manuals/mfg/kitchenaid/khms1850s.html

This is not a fun one if you take a putty knife and go in between the outer door and frame you can release the outer door cover hears the catch over time the door frame becomes brittle so there is a 50/50 chance the frame will break trying to separate it

Replacing the spring isn't very difficult if you're mechanically inclined. You're basically removing a few screws, the front panel of the door is removed exposing only the glass part that's still hinged. The springs are exposed. Hopefully one spring is still in tack so you can see the orientation of how to put the replacement in. It's not very intuitive on how to do this part. Check this link for more details: Microwave Repair