KitchenAid KCMS145J Microwave Oven - Page 4 - Answered Questions & Fixed issues
Would I find the wiring Schematic inside my KitchenAid YKMLS311HBS Microwave?
Yes, unless a technician may have removed it during a previous service. It should be located behind the controller assembly, sometimes in a small envelope.
At my Web site, I have a video showing you how to remove a typical microwave controller in about 5 minutes.
http://www.microwavecontrol.com
if you have other questions, please feel free to contact me directly by email through the Web site or at
[email protected]
11/14/2019 1:57:44 AM •
KitchenAid...
•
Answered
on Nov 14, 2019
•
203 views
KITCHENAID MICRO/OVEN COMBO, EVERYTHING WORKS (CLOCK, TIMER, LIGHTS, OVEN) EXCEPT THE MICROWAVE. IF I TRY TO USE THE MICROWAVE I GET A "DOOR" MESSAGE DOOR IS CLOSED BUT IT ONLY BEEPS AND SAYS DOOR.
Hi Jill, what the screen indicates is that the door is not closed
There are a number of internal contacts that have to be closed for the microwave to work
If any of them are wrong, they can give you that information.
Depending on the brand there may be between 2 or 3 contacts in the door area that generate that warning
Indicate brand, model and type of equipment you are commenting on, in order to find the best possible solution
I wait your answer
Regards Franco Dosil
Hola Jill, lo que te indica la pantalla es que la puerta no esta cerrada
Hay una serie de contactos internos que tienen que estar cerrados para que el microondas funcione
Si alguno de ellos esta mal puede darte esa informacion
Derpendiendo de la marca pueda haber entre 2 o 3 contactos en la zona de la puerta que generan ese aviso
Indica marca, modelo y tipo de equipo del que estas comentando, para poder encontrar la mejor soluci?n posible
Espero tu respuesta
Saludos Franco Dosil
9/12/2019 8:56:11 PM •
KitchenAid...
•
Answered
on Sep 12, 2019
•
251 views
Replace door handle kitchenaid microwave KHMS155L
Here's a diagram of the door. On the inside of the door is the frame, #2. This can be removed very carefully with a small flat bladed screwdriver and work slowly around. The frame is held in place with plastic tabs on frame. Once frame is removed, you should see the two screws that hold the handle in place. Good Luck!
1/29/2019 9:22:48 PM •
KitchenAid...
•
Answered
on Jan 29, 2019
•
287 views
Is it worth fixing our 9 year old above stove microwave Kitchenaid YKHMS2050SS - 2? Random beeping and now not heating.
I'm sorry to say that it's most likely the magnetron that's shorted out (the high voltage device that produces microwaves). It's usually the case with ovens this old that a compatible replacement won't be available.
There's also the fact that your oven is likely way past it's 'end-of-life' date so even if you could find a replacement, other components will begin to fail as more time passes.
In short, save yourself the money, time, and frustration with a new unit. Good luck!
1/18/2019 2:23:21 PM •
KitchenAid...
•
Answered
on Jan 18, 2019
•
222 views
How do I remove door on KitchenAid microwave YKHMS2050SS-2 in order to replace the CTRL-ELEC control card inside the door?
For the KitchenAid microwave, model:
KHMS2050SSS2
I found that i did not have to remove the screw. what i did was loosen the screw as much as it would go before getting tight again.(hard to screw) then on the bottom end of the door hinge (lying on its side) i pryed the bottom hinge off its mount. (with flat head screwdriver) from there i was able to get at the screws to separate the black surrounding stuff from the outside door... then finally i could get inside to get at the door panel controls. I noticed a whole bunch of condensation and on the back of the touch panel (electrical board).. i will replace that part as I think that is the culprit as to why the keys get pressed randomly, beeping randomly and wonkiness :)
4/24/2021 6:22:26 PM •
KitchenAid...
•
Answered
on Apr 24, 2021
•
1,978 views
Kems307dbl6 KitchenAid microwave staying on after you turn it off.
If the magnetron is still operating when off, needless to say , its pretty dangerous. The door lock unit usually has at least 3 microswitches to ensure that the door is closed and ready to operate. 1 of the switches is a safety switch which will cause a dead short if the door is forced open or something goes wrong with the door not closing correctly. This will "blow" the internal fuse in the machine. If the magnetron keeps going, its possible one of these switches have failed or there is an electronic fault causing power to the magnetron in the off position although, I would strongly feel this would be unlikely. These machines are made with a lot of safety devices.
3/9/2018 5:53:55 PM •
KitchenAid...
•
Answered
on Mar 09, 2018
•
135 views
Not finding what you are looking for?