20 Most Recent Leviton 8599 GFCI Receptacle - Page 4 Questions & Answers

0helpful
1answer

How do i fix leviton dimmer switch OB2704 that sputters ?

Haha...with a new one! No kidding, these dimmer switches are sometimes junk. First of all, make sure that you have the right lamps in each socket - and the wattage is lower than the rating on the dimmer. Otherwise, try a new dimmer switch. Let me know if you need further help. Dimmer switches are a little temperamental, so sometimes you get a bad one in the bunch. The load might be near the maximum rating, so they tend to go out sooner. But then there's others that last for a long time. Try this first, and if you need further assistance, feel free to check back with me. Best of Luck to You! Jim
7/19/2014 5:53:22 AM • Leviton... • Answered on Jul 19, 2014
0helpful
1answer

Suddenly, turning on my light switch trips the circuit breaker. I tried changing the light switch and it still trips the circuit breaker. How can I fix this problem?

It sounds like the problem is in your light. Leave your circuit breaker in the OFF position, as well as, the light switch. Then, take down the light, or lights...and check out each connection in the light box. It's best to do one at a time, this way you can go by process of elimination. If there's a lot of lights working off this switch. You can disconnect all the lights from the middle of the room. Put wirenuts on all the bare wires, and then try and see if your lights come on without tripping the circuit. If it trips, then you know the problem is further down the line. I'm going to assume there's only one or two lights, so take them down and check the splices (connections). It seems like you have a loose wire at one of the lights. Please feel free to check back with me if you have any further questions. Good Luck! - Jim
7/19/2014 5:49:03 AM • Leviton... • Answered on Jul 19, 2014
0helpful
1answer

How does a motion sensor light work ?

It picks up movement, and that triggers an internal switch (computer board) to turn light on. If this is attached to a regular light switch, leave the light switch in the ON position. After a few minutes (depending on what you set the time at), the light will go off. Sometimes, people aren't big fans of these switches - because if they are in a room, and there's no activity (eg. working on the computer, reading a book, etc.) - the light will automatically go off. Then, you have to wave your hand - or get up and move - in order to get it to turn back on. So, setting the sensitivity levels, and time intervals are important in relation to the use. Hope this helps! Feel free to ask more question's if you'd like - and I'll answer you as soon as I'm able too...Jim
7/19/2014 5:43:06 AM • Leviton... • Answered on Jul 19, 2014
0helpful
1answer

To wire 3 function control switch

What type of switch and what are you connecting it to?? Need more information.
4/30/2014 12:04:56 AM • Leviton... • Answered on Apr 30, 2014
0helpful
1answer

Instructions to replace pull chain for Leviton Plastic Lampholder model 8827CW2

I believe it is cheaper just to replace it then try to get the parts! You may be able to take it apart and salvage it by using what is leftr of the old pull chain but I am not sure.
4/29/2014 11:00:09 PM • Leviton... • Answered on Apr 29, 2014
0helpful
1answer

LEVITON 7090-BR LAMPHOLDER 3 TERMINALS

I need to ask you for a bit more information. Ordinarily a socket for a 3-way lamp has two external connections, one of which goes to power (black is the standard color) and one which connects to the neutral wire (white is the standard color). The other wire commonly encountered in house wiring is green, which is a ground connection. Lamps normally do not use a ground. The Levitron web page does not flag this socket to be anything out of the ordinary, but neither do they show the connections. So please provide any additional information that you can on this socket. Is it meant to hold a single, 3-way incandescent bulb, or is it for a florescent bulb? Is it meant for a special purpose?
4/22/2014 12:26:51 AM • Leviton... • Answered on Apr 22, 2014
0helpful
1answer

My electrical box has no earth wire how do i go

check your water pipe
11/6/2013 4:34:56 AM • Leviton... • Answered on Nov 06, 2013
0helpful
1answer

60 Hp evinrude outboard starts but stops if I

Check all you linkage assembly on the front Starboard side of the engine.
9/12/2013 1:03:36 AM • Leviton... • Answered on Sep 12, 2013
0answers
0answers
0helpful
1answer

Leviton dimmer

Your product is not identified by number given.Leviton posts manuals online by searching Leviton xxxx .pdf.There is a CPT 602 lighting consoleHowever no result shows online or at Leviton for a 602 dimmerContact Leviton:http://www.leviton.com/OA_HTML/SectionDisplay.jsp?section=37579&minisite=10251Add a comment and attach photo or video for possible identification If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7
5/28/2013 9:27:06 AM • Leviton... • Answered on May 28, 2013
Not finding what you are looking for?
Leviton 8599 GFCI Receptacle Logo

Popular Tags

27 questions posted

Ask a Question

Usually answered in minutes!

Top Leviton Electrical Supplies Experts

john h

Level 3 Expert

29494 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

CJ Rock
CJ Rock

Level 3 Expert

4429 Answers

Are you a Leviton Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Leviton Electrical Supplies

  • Leviton Electrical Supplies

Most Popular Question

gfci oulet triping only thing circuit

  • Electrical Supplies
Loading...