Leviton Combo Switch Neon Lght - 5226-I - Ivory - Answered Questions & Fixed issues

I think putting the card in and out of your phone may have slightly changed the alignment of the card to the connectors in the phone - try entering the card either to the left a little or the right but i have a feeling contact is not being made from the wear and tear. Does the card work in another phone? if yes then definitely not the card... but the fact that you have tried to use 2 different cards im thinking its the phone :(

Yes, but only to operate the neon light. The switch will operate without the neutral. You should have two neutral wires in the box, one in, one out. Besides connecting the IN neutral to the neon light, it must also be connected to the OUT neutral so that your lamp or appliance has a neutral. There might be two silver screws on the switch already connected together for this purpose.

i have the same problem with this phone (along with many many others) sorry to tell you this but this phone is just a piece of JUNK! with many problems and i dont think theres a way of fixing them. i wish i would have known before i bought it :(

It's the same as you wire any single pole switch.

To view the contents, you need to go to "Media" and select "External Memory".

Most LG phones have a spot for the memory card behind the battery. Remove the battery and you will see where the memory card slides in.

i haad the same problem this is what i did..
Firts i downloaded the songs i wanted in limwire
then i made a folder on the desktop and dragged them to the folder
then i went into MY Computer and opened the folder that said sounds in there i made a new folder
then i dragged the files from the folder on the desktop to the new folder in sounds then i put the memory card back into my phone and the songs were there..
i felt so stupid after because it is so simple and i just couldnt figure it out
play around with it you will get it
hope this helps :)

You parallel the contacts then either one or both will turn it on. Both have to be off for the fan to stop.

A Leviton DHC receiver device can look like any other switch or receptacle so if you didn't install it or not provided a map then you'll need to locate it.

Likely the wall switch that originally controlled the light was replaced with DHC device and paired with the 16400 at another location. If you can't identify it, then removing face plates and devices may be the only practical method to locate it.

If your not comfortable with removing devices safely, hire an electrician.

https://www.mc-mc.com/ASSETS/DOCUMENTS/ITEMS/EN/Decora_6375_Catalog.pdf

It's two single pole switches with a removable jumper on one side. With jumper intact, you connect the hot feed to a either screw of the jumper which I belive are brass colored screws.

Then the two induvidual switch poles are the silver screws. Connect fan motor to one and fan light to the other.

If that doesnt work for you, take a picture of the switch and connections and another of wires in fan box and post here.

https://www.leviton.com/sites/REST/controller/LCDownloadController/download/DI-000-VPT24-02F-W.pdf?docurl=/en/docs/DI-000-VPT24-02F-W.pdf Yes, but appears to be non-serviceable... and its probably just a 3.2vdc lithium coin battery inside the case yet they decided to make it so you have to buy a replacement every 10+yrs. Crack it open and see (dill off any rivet heads).

what do you know as "regular " bulbs are they low energy or incandescent

adjust the sensitivity switch

Replace it. They fail and and that is not uncommon. good luck

red never connects to black as that is power to neutral if wired correctly get in a qualified electrician to check the wiring and help you install the unit

yes, take the white wires off the switches and splice them all together with a wire nut. Run a hot wire to each of the switches and then run the switch leg (black) from each of the fixtures to be controlled to each of the dimmers.

If the two load screws are connected with a tab that is the power in side. The color wires are the load.

Seems to be a common problem, you're not alone ( read amazon 1 star reviews). They are $22.00 so you will to dispose of it, if Leviton will not warranty it.

http://www.cooperindustries.com/content/dam/public/wiringdevices/products/documents/instruction_sheets/ri06p_ri06pl_ri061_ri306p_ri306pl_ri101_instructions.pdf

the 5641 is a dual switch for three way and single pole. If you want the switches to operate the CF. Connect the power to one of the two screws on the right side as you face the switch. then connect one wire to the screw on the bottom left side. connect the other screw to one of the two screws on the top left. This assumes the Red and Black you mentioned are the switch legs going to the CF.