Kohler 100-Amp Automatic Transfer Switch - RDT-CFNA-0100A - Answered Questions & Fixed issues


The problem is not likely battery related. It sounds like either an ignition or fuel control relay that is not actuating due to missing electrical voltage.

Kohler 100-Amp... | Answered on Nov 26, 2017 | 58 views


http://www.kohlerpower.com/onlinecatalog/salesservicelocator.htm

Kohler 100-Amp... | Answered on Feb 17, 2013 | 101 views


sounds like the voltage sensor is either mis adjusted or burnt up. Also could be a wire disconnected on the voltage sensor board.

Kohler 100-Amp... | Answered on Mar 11, 2010 | 297 views


Six steps of start-up Shangchai generator set :
A.Unscrew the deflation screw on the fuel injection pump, use the fuel hand pump to remove the air in the fuel system, and fix the adjusting control handle on the throttle position of the suitable starting speed;
B.Pressthe generatorstart button to start the diesel engine. If the diesel engine can't start in 10 seconds (up to 15 seconds), it should wait for 1 minute before starting for the second time. If it can't start for three consecutive times, should check and find out the cause of the failure;
C.After diesel generator set start up, the no-load speed gradually increases to 1000-1200 r/min (note not to run at low speed for a long time). After the diesel engine is preheated, the speed is increased to the rated speed. When the outlet water temperature reaches 55 degrees Celsius and the oil temperature reaches 45 degrees Celsius, full load operation is allowed;
D.After starting the diesel engine, pay close attention to the reading of oil pressure gauge (2.5-3.5kg/C?in normal operation). If the oil pressure gauge does not indicate, stop immediately and check whether the ammeter has charge indication;

E.After the diesel generator set is put into normal operation, should observe the changes of water temperature, oil temperature and oil pressure at any time, and should handle the reading of power meter, frequency meter, ammeter and voltmeter in time if abnormalities are found;
F.When each instrument of the genset indicates normally, can turn on the load switch to send power to the load. With the change of load of the genset, if the frequency and voltage are not within the prescribed range, should adjust the frequency and voltage in time to maintain the rated value. It is strictly prohibited that the genset carry load at low speed, so as to avoid damage to the equipment.

Kohler... | Answered on Sep 30, 2019 | 82 views


contact the maker,
ask them,
or buy one off ebay, using facts above

there is no other way. (there is a parts list at most makers web sites,Valsi

omg first google hit.

http://www.valsi.com.mx/

Kohler... | Answered on Sep 17, 2019 | 57 views


Maybe you can contact the supplier who provide the generator for you. Or you can read manual operation of use.

In the future, if you plan to have a diesel generator set, welcome to contact us: https://www.dieselgeneratortech.com/generator-set/

Kohler... | Answered on Aug 31, 2019 | 62 views


I think you can ask your supplier, they most know their generator.
If you plan to have a new diesel generator set, maybe you can consider Cummins, Volvo, Perkins, as well as China made generator: Yuchai, Shangchai, Weichai, Ricardo etc.
Here is the website:

https://starlightgenerator.en.made-in-china.com/

Kohler... | Answered on Aug 23, 2019 | 40 views


Request the diagrams from Kohler and compare.

Kohler... | Answered on Aug 21, 2019 | 27 views


The engine is failing to run after a commanded start. Repeatedly.

Kohler... | Answered on Apr 19, 2019 | 60 views


Are there any faults listed on the control display? If display is dark then likely a battery issue. Check battery voltage with a Digital Multi Meter (DMM). It should be at least 12.5VDC.

Kohler... | Answered on Apr 17, 2019 | 87 views


check the f1 fuse.

Kohler... | Answered on Apr 16, 2019 | 133 views


Sounds Like possibly the regulator is the issue.
Flightsystems Can test these to see if it is good or not.
also here is a link for the service manual
https://us.v-cdn.net/5020499/uploads/editor/0c/g1lx13xi2vyy.pdf

Kohler... | Answered on Apr 16, 2019 | 760 views


the parts manual is a tp-5317 which I do not have . You said its a dec2? or a fast response 2? What is the part number off the main circuit board in the control box?

Kohler... | Answered on Apr 16, 2019 | 111 views


if you have an scr pack, that has 6 pins, there are two for ac, two for gates, and two for the excitation field.
The two gate wires come off your adc controller.

Kohler... | Answered on Apr 16, 2019 | 115 views


http://www.kohlerpower.com/onlinecatalog/pdf/g2058.pdf
Safety shutdowns:
  1. Loss of coolant
  2. High water temperature
  3. Low oil pressure
Likely one of these. If no indicators at a panel check at the connector.

Kohler... | Answered on Feb 19, 2019 | 73 views


There might be two reasons for the failure of generator auto start.

1. It is the ATS automatic conversion control device that does not issue the start generator command after the mains power failure or phase loss operation, or the self-starting relay failure, which causes the generator to not start itself. This situation is relatively rare.

2. It is the generator start battery failure, and this kind of situation is relatively more.

Kohler... | Answered on Dec 19, 2018 | 152 views

Not finding what you are looking for?
Kohler 100-Amp Automatic Transfer Switch - RDT-CFNA-0100A Logo

5 questions posted

Ask a Question

Usually answered in minutes!

Top Kohler Electrical Supplies Experts

Sheldon Dedek

Level 3 Expert

909 Answers

rjivaro

Level 2 Expert

158 Answers

J. Bradshaw

Level 2 Expert

121 Answers

Are you a Kohler Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...