Kohler K-3386-0 Rialto one-piece round-front toilet with seat and left-hand - Page 7 - Answered Questions & Fixed issues

Most hardware stores carry a good variety of fittings. (Plastic, Brass and iron). Just be sure the leak is the fitting and not just the hose connections. Don't forget to turn the water supply off before cutting the lines.

Which suction cover do you have? Can you email us a photo of the cover you have so we can match it up for you?email to [email protected] Parts Center

yes. Why so much moisture? There shouldn't be any unless you have hot water filling the tank or a spray of water shooting out. Check it out.

Here is the manual for your Samsung Galaxy Note 10.1. Just click on the PDF icon and wait a little for it to load.http://blog.clove.co.uk/2012/08/16/samsung-galaxy-note-10-1-gt-n800-user-guidemanual/

need more information about what kind of control you are using to turn the tub on/off.does it turn off when you can get it turned on?Rod US Parts Center888-521-6183

When a bath pump turns on but does not move any water it is usually because there is an Air Lock and needs to be released.Try this.

• Fill the tub with water
• Turn the pump on
• Unthread the discharge pump union until water starts to squirt out
• when this happens you should hear a big 'swoosh'

if the bath pump starts to discharge water through the jets then you have solved the problem.Rodus parts center888-521-6183

Mold on your jets can come from a variety of places but due mostly to the bacteria in the tub.There are several kinds of cleaners to use in the meantime once you get your trim clean so you can prevent what you are experiencing.Take the trim off and clean them in your sink. DO NOT put them in the dishwasher as it is too hot and will ruin your trim.Here is a link to our site that has different options for cleaning the pipes and keeping the jets from getting yucky.Maintenance ProductsRodUS Parts Center888-521-6183

Your valve inside the tank has worn down and not allowing the water to stop running. Does the water run over the top of the overflow. If so, then adjust your inlet water to a lower level so it will cut off. If that is ok, then likely the flapper is worn out and needs to be replaced.

The workings of a bath jet...From the inside of the Bath there is a wall fitting that threads from the inside of the tub into the jet body located on the outside wall of the tub.If the jet is leaking at this point behind the tub then you should take the wall fitting out of the tub and put a small bead of 100% RTV silicone around the flange of the wall fitting and reinstall it.If however, the leak is from the PVC piping going into the jet then you will need to replace the jet.RodUS Parts Center888-521-6183

Try a pumice stone they work great & can make a toilet bowl look brand new, there with the cleaning supplies in any store.D :)

The chances that is problem you are experiencing is related to the suction cover is extremely remote. The suction assembly doesn't have anything to do with the tub motor operating.The issue is most likely with the motor not working or the air switch in the motor malfunctioning.What does the control look like that you use to turn the pump on/off?Is it an air button or an electronic switch?

Yes, contact Kohler and they have a site you can watch that should be helpful.

Has anything non soluble gone down toilet. If plunging vigorously doesn't work, you may have to take up toilet to see the bottom part. Does any of the water go out of the bowl. Does it eventually go down on its own.

EntsJust replace the assembly and be done with it . It sounds like minerals in the water are building up in the lines and components. It is hard to remove it all.

need to be level 3 then go to that thingy in your nest and go to that door on the left and press mission 1 but you need 1 dosh.How get 1 dosh:got to your nest and press the bincard thingy finally press that stamp thing then you got 1 dosh.from lolo

Look on the internet or call the company.

Toilets seem to run on their own because the water in the tank is seeping our past the seal that was designed to keep it in the tank inbetween flushes. Commonly called flappers, they go by seals, tank balls discs. etc. The K4632 requires a flat seal from Kohler. The actual part number is 1059291, however Kohler may only sell this as part of a kit by a different number with pieces not truely needed in your circumstance.

You should contact them at 1-800-4KOHLER, navigate the prompts, and talk to a service member. You may have to do some research in your area to find a retail or wholesale business that will order this for you. There are circumstances where, with some parts, Kohler will send the parts free to your doorstep. No promises on this one. I have put a link below that will give you a complete parts explosion for your reference.

http://www.kohlerserviceparts.kohler.com/ServicePartsPage.aspx?DocumentID=28e40a91273141a5b63e28ad7230d6a5&ModelID=e9143848792b4415a62b4e384caeb856

Are the particles like white chunks? If yes, I was told to get calcium and lime remover and add it to the water and let the tub run for 30 minutes. Once this is done, drain and then refill tub and run for another 30 minutes to get the lime and calcium remover out of the system. This should help.

sounds like you need a flapper they are all the same for the most part

adjust fill valve turn the water off to the toilet push down on the tension clamp and pull the valve up higher then resecure