20 Most Recent Honda 6370C - Parallel Power Kit For EU3000i - Page 6 Questions & Answers

There are several problems it could be other than fuel. Have you checked you have got a spark. Have you checked that the choke is working. Have you checked that the ignition circuit is live when you turn the key to on. Have you checked the air cleaner is not blocked. Have you checked that the exhaust is not blocked. When was the last time you had it serviced.

How to test your Electricity Generator AVR Brushes and Alternator on... You need to run these tests in the video and come back to us with the results. Send your test results to us here: https://www.generatorguru.com/ask-the-guru/ Then we can tell you what the problem is :)

yes alternators are not rotation sensitive

Try changing bad receptacle.

check for low oil level controller

Is the battery fully charged or has it been load tested?

SSounds like either you have a hole in the muffler or the muffler bolts loosened up.

Sticky inlet valves

You need a volt meter an ammeter and a variable power supply and with ohms law the resistance can be calculated. V=IR thus resistance is the applied voltage devided by the current R=V/I Set the psu till a convenient current is indicated on the ammeter and take an accurate voltage reading and do your calculation. Normal multimeters cannot read reliably below one ohm and these rotors do have a low resistance

THAT POOR ENGINE HAD TO RUN WITHOUT LUBRICANT AND IS SEIZED UP

Hi there! 1) Check battery with a load tester and recharge / replace if necessary 2) Check the ignition switch for loose wires or if the switch is okay 3) Remove the starter and try to run it against a piece of wood ( Have you seen the wooden hammer handle of an auto electrician?) If you can stop it then the motor needs repair/replacement it is often cheaper to replace than repair it excluding labour!! 4) Check ringear on the flywheel and the pinnion of the starter motor for binding and wear. Keep these tips in mind for your Automobiles too

Hi there. 1) Remove all loads and start up.2) Connect a known working load and if it trips on a load too small then the tripswitch is faulty and must be replaced

Hi there I had a similar problem years ago. 1) check brushes on the sliprings of the alternator 2) There is a small pcb on the brush gear and an electrolytic capacitor some diodes etc. check for bad joints or capacitor 3) lift off one brush from sliprings and connect for a couple of seconds a 12 volt battery to it. Why? The rotor must have some residual magnetism for it to develop excitation and sometimes if the genny was not used at all for a long time then that magnetism sometimes die away. It also happen if the genny was disassembled for one reason or another Good luck

Hi, You can get parts from "Generator Guru" for your Dunlite generator and your Honda, as it sounds like the anti vibration engine mounts are shot. Sorry, but I can't help you with the manuals. Kind regards David

My friend has one, and after he starts it, he places a small mini shipping crate over it (like the kind you see in photos of cargo ships). Seems like the crate is made of some kind of plastic or fiberglass, and he has a short flexible steel pipe going out of a small hole that is cut out of the bottom of the back side for an exhaust. Seems to squelch the sound fairly well. Good luck.

yes the tank when all of the bolts removed will slide off the rubber mounts and out one end refitting is to remove the rubber , slide the tank back in and then put the rubbers back under the flange of the tank

hi problem with voltage regulator/ generator as when this functions properly it will raise engine speed hence giving out the power out put required

hi I think the problem is on when the key is turn to rotate and to engage the starter motor and it at this point that the cable curring the current on to the starter motor it then the fuse gets blown , in my opinion this cable is shortening across the chassis causing the fuse to blow, or when it get to the starter solenoid a faulty solenoid absorbs accessed electric current causing the fuse to blow

Generators rely on a residual magnetic field to "kick start" the current making process. Yours has lost this field. Easy enough to fix however. Plug in an electric drill while it's running. Squeeze the trigger and manually twist the end of the drill (this will act as a miniature generator, as the Honda has lost its magnetic permeability and this motor rotating in reverse will generate a small current and restore it). Take care as, as soon as you spin it fast enough to develop a current, the generator will pick up on this current and start generating it's own current; energizing the drill. Once the generator starts generating current, it will repair itself.