American Standard Evolution 2425V-LHO.020 White 5 Feet x - Page 8 - Answered Questions & Fixed issues
I just replaced a cartridge
you need to go back in and check your work it seems that it has been installed in a lower setting look at the directions, most shower assembly's have energy settings.usually just have to move the stopper to the farthest point to the left (counter clock wise).good luck.
11/14/2010 1:43:00 AM •
American...
•
Answered
on Nov 14, 2010
•
129 views
I BOUGHT A FORCLOSED HOME
Inline heaters for whirlpool bathtubs will not and cannot maintain any comfortable water temperature. Their sole function is to slow the time it takes for the water to cool off. The myth of their capabilities has long been a misleading sales propaganda joke in the industry.
Not all manufacturers put their model numbers on their tubs. Those that do will almost always post it on a label in the area of the tub where the back usually rests in the region of the motor but not on the motor itself.
I believe your quarter size cap is an air control for you jet. It controls the amount of air coming out the jet when the tub is full of water and the motor is on. You should see the difference in swirling water turning it from right to left or the other way around. If yours has a leak then I certainly hope you find the Model number. Good luck.
11/9/2010 11:02:51 PM •
American...
•
Answered
on Nov 09, 2010
•
287 views
When i flush the toliet
adjust the chain that connects the flap to the handle give it some slack but not so much as to get chain laying under the flap good luck and hope it helps
11/9/2010 1:33:04 AM •
American...
•
Answered
on Nov 09, 2010
•
509 views
Bought low flow 1.6 litre American standard toilet
Serval reasons: (1) noise from handle chain being metal-consider switching to lighter plastic type. (2) The rubber flap which lifts up when handle is pushed down and seals "when handle is let go" to allow water to fill in take maybe worn to the point of needing replacement-Go to any Lowe's/HomeDepot and they will walk you through replacement process of just removing old one and putting ends in place over hooks to install new one. Takes me 1 minute to do. (3) Adjust the water cut-off valve that supplies water to tank so it can feel up rapidly by just turning the value. If value is hard to turn try using some oil or WD-40 on it. Remember that one way opens to allow quicker fill up and better flush and other way just turns water to toilet off. If now of these things work then just give me a yell and I can advise further.
10/6/2010 10:58:33 PM •
American...
•
Answered
on Oct 06, 2010
•
253 views
I need drivers for motorola router sb5100
I hope you get this... it's posted in the bath section!
An easy answer... Download the drivers here:
http://broadband.motorola.com/consumers/support/default.asp?supportSection=DiscontinuedProducts
9/13/2010 6:24:05 AM •
American...
•
Answered
on Sep 13, 2010
•
50 views
Does a bathroom require an exhaust fan even if it
YES!!!! all a window does is change the vapor into liquid. What is needed is to get the moisture OUT OF THE building. I prefer Neutone 200 CFM unit, for get specs, they are all way too low. You are combating health issues if you allow moisture to remain....mold...
Also, the exhaust ducting needs to run downhill as it exits the building, or you risk moisture dripping from the fan...
Futher, put a 60 minute timer on the fan, and run 45 minutes (at least) for every shower....
9/5/2010 6:30:29 PM •
American...
•
Answered
on Sep 05, 2010
•
256 views
Very slow drainage of a small bathroom sink.
probably hair stuck in the drain. did you remove the stopper "pop up" if no hair or blockage there or in the trap, then its further down, you will need a small snake. 1/4 inch cable works well in bath and kitchen drains.
you can purchase one at home depot.
7/1/2013 3:36:59 PM •
American...
•
Answered
on Jul 01, 2013
•
414 views
When flushing, water does not go down completely.
you can get universal replacement parts from your local hardware or plumbing supply store. For some models you may have to remove the tank from the bowl. Most you can unscrew from inside the tank without removing. Good luck.
8/3/2010 3:43:20 AM •
American...
•
Answered
on Aug 03, 2010
•
122 views
My one piece original porcelain sink and counter
If it is truly a porcelin top then you can use a product called plumbers putty available at your local hardware store. It will conform to the shape of the drain and provide a good seal. If this is a cast marble or resin type of product then plumbers putty will void any warranty and possibly discolor the sink. Ensure it is indeed porcelin before continuing and follow the manufacturers directions for installation. Good luck with your project.
7/16/2010 4:01:53 AM •
American...
•
Answered
on Jul 16, 2010
•
260 views
Not finding what you are looking for?