Top 20 Whirlpool Caresse 2 Person Bathtub Seats Two Adults Questions & Answers

Go to Jacuzzi.com and plug in model and serial no. you should be able to find an operation manual there.

One of these? https://www.amazon.ca/Bath-Drain-Foot-Lock-Plastic/dp/B00L66HVWM Can't you get a drain snake down the side, or these are very effective for pulling long hair blockages and are flexible enough to easily go around corners. I use mine every 6 months. The Green Gobbler cleaner is also very good, or use Draino Gel. https://www.amazon.ca/dp/B00IJFU440/ref=sspa_dk_detail_1?psc=1&pd_rd_i=B00IJFU440&pd_rd_w

Green Gobbler Dissolve Hair and Grease Clog Remover

Home Depot https://www.homedepot.ca > ... > Drain Cleaners Highly effective against grease, hair, soap, and fats. Green Gobbler Dissolve Drain Clog Remover is odourless, nonflammable, and safer to use than ... $18.98 ..

Didn't I answer this yesterday? I said a local plumber, a spa pool shop, fill them with silicone if you aren't going to use the jets again, or just replace the tub if it is leaking. We don't charge for anything. We are Fixya, we only supply information, nothing else. Fixya isn't really the place to ask for quotations. General plumbers https://www.google.com/search?q=santa+fe+nm+plumbers or specialist plumbers for spa baths https://www.google.com/search?q=santa+fe+nm+spa+bath+plumber ..

There is help and videos in this link https://www.google.com/search?q=aquaglass+tub.+replace+toggle+switch If it is completely enclosed, a plumber will normally make an inspection panel from the other side of the wall to gain access. https://www.google.com/search?q=aquaglass+tub+installer ..

every motor has a frame size and horsepower listed on it. search for a new one that way. i would think since its driving a pump it will need to be a totally enclosed/driproof model

Search google

Did you turn the outer rings on the jets? They could be turned off. They are used to adjust the bubble flow, but also to turn them on or off.

Check breaker and reset switch.

no power motor seized up thermal overload button needs pressing in

first of all you need to be draining the tub completely and removing any bath mats or items from inside. Fill the tub with hot water, ensuring that the jets are covered. You can use white vinegar, 2-3 cups of white vinegar directly to the water in the tub. Turn on the whirlpool system and run it for 15-20 minutes. While the jets are running, use a soft-bristled brush to scrub the jet openings and the interior walls of the tub. Drain the Tub: Refill the tub with clean water and run the jets again for another 10-15 minutes to rinse out any remaining cleaning solution. This should help. This is what I did with mine

I would do it chemically with solution designed for the job. Or maybe just put vinegar in the water and let it circulate for a while and then replace the water.

Might not be the button, they use air pressure to travel through a tube to a remote switch near the motor. You have to get under it to see if the tubing is loose or cracked.

Hi Virginia, I've done some research on tubs with jets, and from what I've read I wouldn't put anything granular in the water. The granules may damage your pump and also when the water stops some granules will be left in the pipes, where they will decompose and turn into.... well, I don't think it'll be nice.

try a plumbers shop as it is a whirlpool tub you state that it is a whirlpool tub then you say don't know what brand of tub it is whirlpool is a brand name any way the plumbers display of bathroom units and tubs will help you as the jets used are generic and not specific for the tub

Manuals and Troubleshooting Whirlpool whirlpool double door wiring Google Search

Have you tried the button on the top ledge?

contact the company or set them before you turn it on

The switch or a relay needs to be replaced. If the switch is a push on - lock - push off, then it is bad. Probably the locking mechanism on the switch has worn or failed. It it is momentary on - off, then a relay that might be in line with it would be bad. Without the schematics, it is hard to troubleshoot at this time.

put your hand up under the edge of the button and push in the two plastic prongs in and push the switch up out of the spa they normally just push in and the prongs spring out to hold the switch in place

Disconnect power from the system. 2. Purchase a can of www.ultra-lube.com (This type f lubricant will not cause breakdown of rubber, silicone or plastic seals) multi purpose lube. HomeDepot sells it. Black green and silver spray can. 3. Remove the knob using the right size Allen wrench. 4. Spray lube into the neck of the actuator. 5. Wipe off any lube from the knob shaft. 6. Re install the knob and push pull a few times to distribute the lubricant. 7. Restore power and test system.

If this does not solve the problem then there may be a mechanical failure in progress. Go online at the manufactures website to order a new switch. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/john_28069c9efb56199d