20 Most Recent Xerox WorkCentre 3325/DNI - Multifunction fax / copier / - 3325/DNI - Page 6 Questions & Answers

https://printcopy.info/?mod=erc&brand=Xerox&model=WorkCentre+5024&code=061-321

https://www.support.xerox.com/en-us/article/en/1101550.html

You may need to reinstall firmware

http://www.fixya.com/support/t24930515-code_2220000 https://www.fujixeroxprinters.com.hk/downloads/uploaded/CM215b_UserGuide_64e7.pdf Unable to determine reason for 2220000 code, but it may be possible to contact FUJI XEROX for assistance. Manuals have contact information. https://www.fujixeroxprinters.com.hk/downloads/uploaded/CM215b_UserGuide_64e7.pdf

That is a fuser overheat code suggest you have a techintion repair or replace the fuser

If you wish to get some details; check the site linked here. Pull up older posts..... http://electro-medical.blogspot.com/

Select system conf

Switch the power off, remove the HD, switch the power on, wait until machine warming up.
Switch the power off, reinstall the HD, and switch the power on.

give me answer please

[Cause] During the transfer using SMB of the scan to PC feature, the SMB server could not be found. [Remedy] Take one of the following actions, and try again: Check the following to see if the destination SMB server and the machine are set up properly for network communications: - Check the network cables are plugged in securely. - Check the TCP/IP settings. - Check communications of port 137 (UDP), port 138 (UDP), port 139 (TCP). Check the following to see if the computer correctly works as an SMB server. - Check if the file sharing service for Microsoft Network is activated. - Check if [NetBIOS over TCP/IP] for TCP/IP is activated. - Check if the file sharing service (using communication through port 137 (UDP), port 138 (UDP), and port 139 (TCP)) are authorized for the Firewall settings. For communications which exceed the subnet, check the WINS server settings, and check if the server address can be resolved correctly. For Windows NT 4.0 Server/Workstation, use the following steps to see if the NetBIOS interface device is activated on the destination SMB server: 1. Select [Start] > [Settings] > [Control Panel]. 2. Display [Services], then select [Messenger] service. 3. Select [Startup] > [Auto] > [OK], then select [Close]. 4. Select [Devices] in the [Control Panel], then select [NetBIOS Interface]. 5. Select [Startup] > [Auto] or [Manual] > [OK], then select [Close]. 6. Reboot the

Can you feel any physical heat from the fuser. Sounds like either the thermistor that controls temperature or the lamp failed.

Try:

1. Press the Machine Status button, then Tools tab.
2. Select the General feature, then Feature Installation.
3. Enter the Feature Key on the Feature Key screen to reset the Administrator credentials to the default values ( admin and 1111).

Black toner dispense fault. Check for obstructions on dispensation of black toner to the developer housing . Then NVM 362-371 if it 3 you must reset it to 0

https://printcopy.info/?l=en&mod=erc&brand=Xerox&model=WorkCentre%205021&code=062-277 Xerox WorkCentre 5021 Error Codes

Code

062-277

Description

DADF Communication Fail Transmission cannot be established between the ESS/MCU PWB and the DADF PWB.

Remedy

1. Turn the power OFF and ON. 2. Turn OFF the power and check the connections between the ESS/MCU PWB J421 and the DADF PWB J751, J752 for open circuits, short circuits, and poor contacts. 3. If no problem is found, replace the following parts in sequence: • DADF PWB (PL 56.2) • ESS/MCU PWB (PL 18.1)

May be a defective toner cartridge - try a another to find out.https://www.support.xerox.com/en-us/article/en/1849270.html

install phase incomplete in xerox 5755 code 02-540.00

https://www.xerox.com/download/security/security-guidance/4e9d5-4bb5d6c68c200/cert_WorkCentre7525-7530-7535-7545-7556_Guidance-v1-4.pdf

This may require replacement of the fuser unit as mentioned on page 774 of this document, meant to be used only by Xerox technicians. I would not even be accessing the document on my business computer as it appears from a foreign source. https://docviewer.yandex.ru/view/0/?*=L3ZM3UDX5Z6%2FXfW9EzCsDWJS1297InVybCI6InlhLWRpc2stcHVibGljOi8vRVh2M2Y1Yko5ZjdXcHJjdnlxeHVpVnNYTWxteXJwNG54Mkx6SmE1MHU2cz0iLCJ0aXRsZSI6Ilhlcm94X1dDXzUzMzVGX1NELnBkZiIsInVpZCI6IjAiLCJub2lmcmFtZSI6ZmFsc2UsInRzIjoxNTA1NjM0NDQ2NjgxfQ%3D%3D

This code means toner mot fail so check for toner caking after that go mvm location 762-032(write down current val just in case) whatever value ...A Hard reboot might be needed shut it down an turn up after 5 minutes

you need a service pack to install. the code is a programming mistake/ inability to deal with rotating something see this link and check your software version to see if you need the SP. I guess you do. http://www.support.xerox.com/support/xerox-color-550-560/file-download/enus.html?operatingSystem=winxp&fileLanguage=en&&associatedProduct=XRIP_550_integrated_Fiery&contentId=120034&from=downloads&viewArchived=false