The Konica Minolta R2 Super 700 is a high-speed digital duplicator that uses a pump to supply ink to the print head. The problem you're describing, where the P2 pump makes a loud noise, could be caused by several factors.
Here are a few suggestions for troubleshooting the issue:
Check the ink supply hoses for any kinks or blockages that may be causing the pump to work harder than normal.
Check the P2 pump for any signs of wear or damage, such as a broken or worn impeller.
Check the P2 pump's filter for any blockages and clean if necessary.
Check the P2 pump's voltage and ensure that it is within the correct range.
If the problem persists, it may be necessary to replace the P2 pump.
If you're experiencing an installation error with your Konica Minolta C224e drum unit, it may be caused by a problem with the drum unit's sensor. The sensor is responsible for telling the printer that the drum unit is correctly installed and ready for use.
Here are a few steps you can try to troubleshoot the issue:
Make sure the drum unit is properly seated in the printer. The drum unit should click into place when it is properly installed.
Check the drum unit's sensor for any debris or buildup that may be blocking it. Clean the sensor with a soft, dry cloth.
Check the drum unit's connector for any damage or debris that may be preventing it from making a proper connection with the printer. Clean the connector with a soft, dry cloth.
Try to reset the drum unit by unplugging the printer, waiting a few minutes, and then plugging it back in.
If the issue persist, try to replace the drum unit to a new one.
If these steps do not resolve the issue, it may be necessary to contact Konica Minolta customer support for further assistance.
There could be several reasons why your Konica Minolta 360i machine is producing thin, weak color on one side of the page when printing on A3 paper. Some possible causes include:
Ink or toner levels: Make sure that the ink or toner levels in your machine are sufficient. If the levels are low, you may need to replace the ink or toner cartridges.
Print head: The print head may be dirty or clogged, which can cause weak or uneven color. Try cleaning the print head to see if this resolves the issue.
Paper quality: The quality of the paper you are using could be impacting the print quality. Make sure you are using high-quality paper that is compatible with your machine.
Printer settings: Check the printer settings to make sure they are optimized for the type of paper you are using. You may need to adjust the settings to get the best print quality.
If you have tried these troubleshooting steps and the issue persists, you may need to seek the assistance of a technician. It is possible that there is a more serious issue with your machine that requires professional repair.
C-2152 is a trouble code that may be displayed on some Konica Minolta printers. This code generally indicates a problem with the printer's fusing unit, which is responsible for bonding the toner to the paper.
Possible causes for this error code include:
A malfunctioning or damaged fusing unit
Toner or toner waste accumulation on the fusing unit
A faulty thermostat or temperature sensor in the fusing unit
A problem with the power supply to the fusing unit
To troubleshoot and fix this error, you may need to perform the following steps:
Check the fusing unit: Inspect the fusing unit for any visible damage, debris, or toner accumulation. If necessary, clean the unit and check for any loose or damaged components.
Replace the fusing unit: If the fusing unit appears to be damaged or malfunctioning, it may need to be replaced.
Check the power supply: Make sure the printer is properly connected to a working power outlet, and check the power cord for any damage or loose connections.
Check the thermostat and temperature sensor: These components are responsible for regulating the temperature of the fusing unit. If they are faulty, they may cause the C-2152 error code to be displayed.
Main Board for the copier that receive info from the Document feeder is causing that code. Is your machine DS version or none version? Could have the incorrect document feeder for that machine, or the small printed circuit board that come with document feeder is bad. Could try a different document feeder. Might also see if you can have tech come and re-flash the copiers firmware specially the document feeder and or the MFB Board (Multi Function board) is bad.
1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Reset key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
If the code comes back replace the fuser unit (HOT PART) Do not continue to reset. Could start a fire that would ruin a perfectly good day! Once the fuser is replace may require to reset the it again
The motor that moves the LASER beam around is bad. The motor is housed inside the Printhead which is consider one unit. You can just replace the motor you replace the print head.
Turn ON the power switch with the Stop/Reset key held down. code is for the fuser the hot part that fuse the toner to the paper. Replace may be needed.
Well there is a chip on the toner cartridge you would have to replace that as well since you can get them replacing the toner will do no good as the printer does not know you replaced the toner. Buy a proper toner cartridge.
Code is assigned to MFB (Multi-Function board). To reset power off wait 10 seconds power on. If code returns then MFB board is bad. Might try updating firmware. Have tech do that as Konica Minolta Firmware is located on a secure website. They have to protect there OS's software.
exposure lamp or CCD issue. both located under the big glass. The CCD is the large black device on the right. The scanner is device on left that lights up scan a document though the Doc feeder or main glass.
try this reset
FIRST, if this code comes back. Have a technician look at it DO NOT CONTINUE TO RESET the code!!!! AS this is for the Hot Part called the destroy the lamp or CCD
1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
