20 Most Recent
Konica Minolta Bizhub C454 Color Copier - Page 2 Questions & Answers
HOW TO RESOLVE CODE C-2221 KONICA MINOLTA BIZHUB C5500
1.The terminal for the first transfer pressure/release sensor is not connected properly.
Reconnect the terminal.
2.Failed PS15 (p/n 08AA 8551 2).
Test photosensor, PS15, in the I/O State Confirmation Mode, 48-0HIGH = home position or LOW = Other than home position by activating M19 (p/n 08AA
8003 0) transfer pressure/release motor, 48-0, 48-1, 48-2, or 48-3. Replace thephotosensor or motor as needed.
3. Possiblefailed Transfer/Pressure Release motor (M19).
Check the operation of the motor(p/n 08AA 8003 0) in the I/O State confirmation mode for proper operation with code 48-0; this should rotate the motor
constantly. Replace motorif needed.
Also check for possibleopen ICP fuses, ICP3 (5V DC)and ICP4 (24V DC) on the AC drive board (p/n A03U H520 01). Replace the drive board as necessary.
SPECIAL NOTE : Solution contribution by KMBT (Japan) and Freddie Burnham, Production Print/SSD
Good morning, my Konica Minolta 190f says:please call service 001,what will I do to resolve this
Error code 001 is a generic service call error, and it could be related to various problems within the printer.To resolve this issue, follow these steps:
- Power Cycle: Start by turning off the printer, unplugging it from the power source, and waiting for a few minutes. Then, plug it back in and turn it on again. Sometimes, a simple power cycle can clear temporary glitches.
- Check for Obstructions: Ensure that there are no paper jams or any obstructions inside the printer that may be causing the error. Clear any paper jams carefully if you find any.
- Reset Printer: Look for a reset button or a specific key combination in the printer's manual or documentation. Try resetting the printer to its default settings to see if the error clears.
How to remove white light appeared on artwork in konica minolta buzhub c454
If you have already replaced the charging corona, developer powder, and cleaned the laser unit, but the problem of a white light appearing on the artwork persists on your Konica Minolta Bizhub C454, here are a few additional steps you can take:
- Check the transfer belt unit: Ensure that the transfer belt unit is clean and free from any debris or toner particles. You can gently wipe it with a clean, lint-free cloth. If the transfer belt is damaged or worn out, it may need to be replaced.
- Inspect the imaging unit: Check the imaging unit (drum unit) for any signs of damage or wear. Make sure it is properly installed and securely seated in its designated position. If the imaging unit is defective, replacing it might resolve the issue.
- Perform a density adjustment: The Bizhub C454 usually has a density adjustment function. You can access this in the device's settings menu or through the control panel. Performing a density adjustment might help improve the print quality and reduce any unwanted artifacts.
- Check the print settings: Ensure that the print settings on your computer or the printer's control panel are appropriate for the artwork you are printing. Adjust the print quality, resolution, and any color settings as needed.
- Update the firmware: Visit the Konica Minolta website and check if there are any firmware updates available for your Bizhub C454. Updating the firmware can sometimes address software-related issues that may be causing the white light problem.
If none of these steps resolve the issue, it is recommended to contact Konica Minolta's customer support or a certified technician for further assistance. They will have specialized knowledge and tools to diagnose and fix the specific problem with your machine.
I have a konica minolta c250i, the magenta is not printing on the paper, it print out as yellow. other colors are perfectly ok
There are several reasons why your Konica Minolta C250i printer may be printing magenta as yellow. Here are some troubleshooting steps you can try:
- Check the magenta toner cartridge: Make sure that the magenta toner cartridge is properly installed and has enough toner. If the toner cartridge is low or empty, replace it with a new one.
- Clean the printer heads: Use the printer's cleaning function to clean the printer heads. This can help remove any clogs or buildup that may be preventing the magenta ink from flowing properly.
- Check the printer settings: Check the printer settings to make sure that the correct paper type and color settings are selected. If the printer is set to print in grayscale or black and white mode, it may not use the magenta ink.
- Perform a firmware update: Make sure that your printer has the latest firmware installed. Sometimes firmware updates can fix issues with printing quality.
- Contact Konica Minolta support: If none of the above steps solve the issue, you may need to contact Konica Minolta support for further assistance. They may be able to diagnose the issue remotely or send a technician to your location.
I hope these steps help you resolve the issue.
I have a konica minolta c8000 with error code C-3151, what does it mean?
Error code C-3151 on a Konica Minolta C8000 printer indicates a "Fixing Film Transport Motor Lock Problem." This error typically occurs when the flexing film is stuck or there is a problem in the film transport module. In order to fix the issue, the printer should be opened up and the fixing film should be checked for any obstructions. If the issue persists, the motor unit and flexing film may need to be replaced.
I have the error C-D010 in konica minolta bizhub 367, how to enter service mode?
The function proceeds in the order of Physical Format to Logical Format.
• If the hard disk is yet to be formatted, the malfunction code "C-D010" will appear. Ignore this code and continue with the formatting procedure.
Use:
• When the hard disk is mounted.
• When the hard disk is to be initialized. (Physical Format to Logical Format)
Adjustment
Procedure
1. Call the Service Mode to the screen.
2. Touch these keys in this order: [State Confirmation] ? [Memory / HDD Adj.] ? [HDD
Format].
(1) Physical Format
1. Touch [Physical Format].
2. Press the Start key to start the formatting sequence.
3. The sequence will be automatically terminated as it is completed.
4. Turn off the Main Power Switch and turn it on again more than 10 seconds after.
(2) Logical Format (Only when initial is set up)
1. Touch [Logical Format].
2. Press the Start key to start the formatting sequence.
3. The sequence will be automatically terminated as it is completed.
4. Turn off the Main Power Switch and turn it on again more than 10 seconds after.
How do i correct error p-28 on my konica minolta c654
Error code P-28 on a Konica Minolta C654 printer indicates that there is a problem with the communication between the printer and the computer. This error can be caused by several different issues, here are a few possible solutions:
- Check the cable connection between the printer and the computer. Make sure that the cable is securely connected and that there are no damages.
- Check the printer driver on the computer. Make sure that the driver is up-to-date and installed correctly.
- Restart the printer and the computer, and then try printing again.
- If the issue still persists, try reinstalling the printer driver.
- Try to connect the printer directly to the computer via a USB cable instead of a network connection, if it is possible, and see if it works.
- In some cases, this error may be caused by a malfunctioning network card or control board. If none of the above solutions work, it is best to contact a technician or the manufacturer's technical support for further assistance. They will be able to provide more specific instructions for your specific model.
Note that these are general suggestions and your specific case may require different actions.
Regenerate response
Konica Minolta Bizhub C280
The problem you are experiencing with your Konica Minolta Bizhub C280 not accepting new print jobs after changing the K drum and developer, could be caused by several reasons:
- The new K drum and developer might not be compatible with the printer, please check if the new parts are compatible with your specific printer model.
- The print queue on the computer may be stuck or corrupted. You can try clearing the print queue by going to the control panel and searching for "printers" and then right-clicking on the Bizhub C280 and selecting "See what's printing" and then "Cancel all documents"
- The firmware of the printer may need to be updated, you can check the Konica Minolta website for any firmware updates for your specific model.
- The 500,000 page count that you mentioned, could be a "life counter" on the printer, some printers have a maximum page count before needing maintenance, so it might be related to the issue.
- The issue may also be related to the print server. You can try resetting the print server or reconfiguring it, or you can try connecting the printer directly to the computer and see if that resolves the issue.
- Sometimes, resetting the network settings on the printer can also fix the problem. You can try going to the printer's web interface and find the network settings, and reset them to factory defaults.
It is highly recommended to consult the user manual or the technical support of Konica Minolta for specific instructions on how to perform these troubleshooting steps and avoid causing any further damage.
Not finding what you are looking for?