Top 20 Stanley Lawn Mower. 54 in. 24 HP Kawasaki FR691V Heavy Duty Zero Turn Questions & Answers

Make sure it has the right amount of oil in the crank case, if over filled the oil will foam and flow out any place it can, Worn piston rings can cause blowby into the crank case , causing oil to escape from the dipstick tube.

Chapin makes sprayers. They have parts. Just give model #. Phone 1-800-950-4458. Located in N Y STATE. Pump rebuild kit is $25.00 Inc shipping.

Is tranny and various speeds working properly? How about the throttle control? Do you have it set for higher speed?

Not without a model number!

Try tilting the machine backwards for a few hours. It may be oil on the piston that is causing a vaccum

The valve-o-rings + [ parbaks seals ] where the pressure can be adjusted with. Control the water inlet filter or hose that there are no waterlock couplers are used or is mounted on the wrong site on the hose , that it is used as water inlet on the tap.

Hi Chris: It is usually easiest to rest the weight on the tailgate of a pickup truck (or some other device) and then slip out of the harness. Another technique is to lift bend forward while at the same time rising one shoulder and lowering the other. That will create "slack" on the low shoulder side allowing you to get that arm out. Cheers

Disconnect the wand from the washer if you get water coming out of the discharge, the problem is in your wand or the line is plugged going to the wand.

If you switch the unit on and water spits out of a connection, that's where you either put the O-rings or replace them.

If it is a screw drive like mine all I needed to do was lube up the screw with a product called "fluid film" and all was ok. The screw was binding making the sensor think the door was blocked and it would go back up.

HERES A LINK,I THINK ITS WHAT YOU NEED.... http://docs-europe.electrocomponents.com/webdocs/04f7/0900766b804f72b4.pdf

Try manufacturer web site.

Gerard, PLEASE contact me at (941) 391-5152 or [email protected] so I can hire you to replace the batteries in my Stanley barflex bf0109 light like you did above with vastly more run time mAh. I need someone to do it for me. I'm disabled. I just joined fixya.

Thanks,
Wallace Franklin Banach...

hi thre digslogs

pull the kill wire from ignition coil if a cdi type ignition unit and see if spark when hot , if not faulty coil indicated replace coil and set air gap
cheers take look

pauly46

Hi maraleequanb... I do not know this lock personally but according to what I am reading you do not have to use the key every time, only if you want to lock it while your away. I have found this quote about it on a website along with some others you might be interesting in reading . Please take time to rate me thumbs up **************************************************************************************************************** "4.0 out of 5 stars Great Gate Latch - Installation Instructions lacking, May 4, 2010 By M. D. Heidenreich "DIYWhenICan" (Dayton, OH USA) - See all my reviews
(REAL NAME) Amazon Verified Purchase(What's this?) This review is from: Stanley Lockable Gate Latch With Dual Access (S836-171) [Misc.] I installed this gate on a 6' tall by 4' wide cedar gate latching to another smaller gate section. The smaller one has the post the larger side has the catch. The ability to push a button and open from the inside was the key selling point for me, being able to lock it is secondary but still will be nice when on vacation. We had one similar but we had to drill a hole and run a string and half the time manually latch the gate. This latch solved that problem completely. Gate now shuts and latches without a hitch. Now to the installation instructions: First - DO NOT USE the little grey PVC tube unless you have a hollow vinyl post - would of been nice if this was in bold print somewhere in the instructions. I tried to use it on the wood gate and spent 45 minutes on it before I finally found the teeny tiny writing saying not to use unless on vinyl. Second: I typically do well with pics. in instructions rather than a bunch of drawn out written explanations - not so with these instructions. From the look and my experience you could install on any gate set up so chances are you can make it work. I read other reviews complaining about the plastic and was prepared for that but was pleasently surprised with the solid feel and sturdy construction - time will tell but if it lasts two years, for the money, I'd say it's money well spent. My 4 stars are due to the instructions not the product. "

More quotes and pictures of the lock.
http://www.amazon.com/Stanley-Lockable-Latch-Access-S836-171/product-reviews/B002L2R7K6

At the lower part of your sharpshooter there is a port,kindly remove it by pulling that port.And after you pulled it put the brads and put it back to the nailed.

Your stud finder keeps beeping because old plaster walls have lath boards behind the plaster that are attached to the studs and running horizontally. Try adjusting the sensitivity of the stud finder by placing it on the wall and turning the sensitivity down until it just stops beeping. Then move it back and forth in a wide enough arc to be sure that you have crossed a stud, turning up the sensitivity ever so slightly until you get a tone when you cross a stud. Hope this works out for you.

Your door jumped out of synch What you need to do is turn the open close knob on your closer toward the open mode until it stops opening when you close it.

Your sensitivity may need to be adjusted