20 Most Recent Troy-Bilt Chipper Shredder - Page 3 Questions & Answers

there's are websites all heavy equipment repair issues servicing, loading, wiring, engine problems everything is covered here its a must try for those who aren't fully equipped with tools or knowledge

hello for heavy machinery u will find a lot of wiring diagrams and circuit diagrams and stuff like this at few sites I know the girl in the chat box can help u instantly

you can get guide from https://www.reliable-store.com/

1. error codes/ fault codes,
2. wiring diagrams, schematic diagrams,
3. torque specs,
4. engine info,
5. switches functioning,
6. assemble, disassembly, complete refurbish, repair, installation every single thing is covered

within seconds u can get the access and it's totally illustrative complete

I have all equipment manual Site :- Heavy Equipment Service Manuals

HI believe that we have a 47287 8 hp chipper/vac where would i find Model on chipper vac

Be sure to compare the removed belt to the new belt for length and width. Often belts get mis-packaged into the wrong container or otherwise mis-labeled. A belt that is even 1/4" longer will not provide the correct contact tension. Also be sure the pins that the carriage moves on are lubricated. Corrosion can keep the carriage from keeping tension on the belt as the carriage weight can not tension the belt. Hope this helps.

.030

Troy Bilt Part Number 1762636

Genuine Troy-Bilt Parts - troybiltpartsonline.com‎

Adwww.troybiltpartsonline.com/‎Troybilt Parts Lookup

Common Troybilt Parts

Briggs & Stratton Parts

Just found some parts for my Troybilt Gardenway chipper-vac Model 47279 on this website http://www.partsandservice.com/bin/ipl.cgi
I would think they might have something for your machine.

part number for these blades is 1772231MA

I bought a bad photocopy of the Operator manual from a seller on eBay, and put it online:[URL="http://asavage.dyndns.org/Troy-Bilt/"]http://asavage.dyndns.org/Troy-Bilt/[/URL]It\'s not great quality, but it\'s better than nothing.I\'ve got some parts manual pages there, too. Also of dubious quality, but you can make out the part numbers.

If it's the same as for my 47287 (8HP, 3 spd + reverse), it's part No. 1901996 and is NLA. Let me know if you find a source, mine is also broken.

Be gentle, that shift cable is NLA (I know, I need one).It sounds as if the belt idler is not releasing. Take a look at the belt engage cable, Ref. No. 9 on this exploded view:ftp://asavage.dyndns.org/Troy-Bilt/47287-ChipperVac/47287c-47287c02.07.gifThe spring at the end of that cable is what releases the idler from the belt. Another pic of the spring is near the idler arm Ref. No. 13 on this view:ftp://asavage.dyndns.org/Troy-Bilt/47287-ChipperVac/47287c-47287c02.05.gifIf that spring is broken or missing, that would give the symptoms you describe.HTH

put a tube in it once they start leaking around the bead they are hard to reseal again

is the gas any good?is it newer than 30 days old gas is only good for 30 days in small engines

check for spark is there a low oil shut off and the oil level is a little low ?

That question is posted in the free portion. It is funny isn't it, it asks for money and then when you refuse, you do not know whether is posts or not, it does in the free section.

I'm a step behind you on this problem. I have the exact same model, and the belt fell apart. I was given this unit, and I doubt the belt was ever replaced before. Do you happen to know what size belt it is? I tried calling Sears; and they didn't have the part anymore and they were of no use on getting a cross reference number. Any help would be greatly appreciated.

The 3 models of Troy Bilt chippers are on this page:

http://www.troybilt.com/webapp/wcs/stores/servlet/category2_10001_14102_54996_54992_54992_-1

Click on the picture of your model and you are given the option of downloading the manual. You need the serial number of your machine to do this.

Hope this helps!