Question about 2002 Yamaha V Star 1100 Classic

1 Answer

Can't get it to idle without having choke nearly fully engaged. already tried adjusting throttle to no avail

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

It could be a possible air or vacuum leak.

Posted on Jul 10, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Briggs Stratton 5hp I/C starts ok, runs, but will not rev


My money is on a partial blockage of the main jet or the passageway to it. You're having to force it to run through the idle jet by fully choking the incoming air. There's not enough gas coming in with the choke open to allow it to run.

I'm thiniking total carb disassembly, carb cleaner and an air compressor combined with a ton of patience will take care of the issue.

Mar 31, 2015 | Briggs & Stratton Briggs Stratton...

1 Answer

My e series 142 spins the chain and idles insanely fast when I have the choke pulled out. Then when I give it throttle it calms down and then I can barely keep it idling. with throttle all the way pulled...


Check air filter- clean or replace, Make sure you have fresh fuel, A new spark while you are giving it a service, Do you know how to tune the saw? Start with basic settings 1 turn on the low and 1 turn on the high And adjust from there, You might have turned the idle up too high. The choke should always be fully in when saw is running. Hope this is a good start

Oct 04, 2013 | Husqvarna Garden

1 Answer

Choke problems


I take it that you have a carby in which case adjust the choke cover so that the cam engages the throttle lever and holds the throttle open until the bi-spring in the choke cover moves enough to move the cam out of the away allowing normal idle. If you have efi (Not from your choke word) then run fault codes and see which sensor is faulty. There should be an idle speed around 1200 RPM idle in efi for around 3 minutes and then the idle should drop back.

Sep 22, 2013 | Dodge Ram 1500 Cars & Trucks

1 Answer

2007 Yamaha 115 Hp 2 stroke idle problem


Check the idle mixture. Sounds to me like it is too lean.

Mar 20, 2017 | Clymer EvinrudeJohnson Outboard Shop...

1 Answer

I have a 1990 jeep wrangler yj . 4.2 with a used weber carb 36/32 . it stalls at a stop sign . the vacume lines seam to be hooked up ok the back port above the throttle is caped off the idle mixture s


The idle mixture screws do not control the idle. Is there no idle screw? If you have an anti-dieseling solenoid on the idle screw, make sure it is coming on with the ignition switch and use it to adjust the idle. Set the idle and then adjust the misture screws to maximize intake vacuum at idle. Readjust the idle after adjusting the idle mixture. The port at the back of the carb is not used in all systems. If you have a distributor with vacuum advance, make sure the correct carb post is connected to the distribtor. Adjust the choke and fast idle to engage when the engine is cold.

Jul 15, 2017 | Cars & Trucks

1 Answer

Have new 450 and is very difficult to start. Lost or didn't get book. How do I start it and re-start it while still warm??


Start procedure is, push the primer as many times as it takes to 3/4 fill the bulb ( you cannot over prime it ) pull the blue choke lever fully out,place the saw on the ground with your right boot through the back handle, crank the engine until it fires once, do not continue to crank the engine with the choke out ( they will not run on choke, only fire ) push the choke fully home, crank the engine until it starts, blip the throttle trigger to bring the saw to idle, warm engine, pull the choke fully out and push in again without cranking engine, this will engage the part throttle, crank the engine until it starts, blip the throttle to bring the engine to idle.

May 18, 2011 | Husqvarna 450 e-series 18" Chain Saw

1 Answer

My 2002 honda xr200r will only start with full choke on and at that I must play with throttle


Although there are three positions to the choke, full choke is applied in the Up position. If you are having problems starting the bike try adjusting the idle and air adjustment screws. Idle is on the side and air is centered under near the float bowl. Consult the owners manual for the # of turn out from an easy seat. If that doesn't work remove the carb and all jets and screws and clean. also make sure that the decompression cable is in good working order!

May 04, 2011 | 2002 Honda XR 200

1 Answer

2nd use of chainsaw pp3516avx, it won't start, choke lever will not stay extended. I followed the instructions to start and nothing works


The choke system is connected to the half throttle position, if you lift the throttle trigger the choke pull will automatically return, whilst trying to start do not lift the throttle trigger, the starting procedure is, pump the primer bulb as many times as it takes to 3/4 fill the bulb, pull the choke pull fully out, this will switch the saw on and engage the half throttle, crank the engine until it fires once, do not continue to pull,it will actually not run on full choke, if you do continue to crank with the choke fully out, you will very quickly flood the engine, now push the choke fully in, now crank the engine until it fires up, lift the throttle trigger once, this will dissengage the half throttle, and it should now come down to idle.

Mar 19, 2011 | Poulan Pro 16-Inch 38 cc Anti-Vibration...

1 Answer

22 horse kawasaki riding lawn mower will not run at full throttle unless the choke is engaged


That is not a good situation. Too rich of a fuel adjustment can wash the bores out on that engine and prematurely wear it out! You will likely need to have the carburetor linkage and plate adjusted so that full throttle operates without engaging the choke. (If this is a single lever that you slide from slow, idle speed to fast, then on to choke)

May 09, 2010 | Husqvarna Garden

1 Answer

My 400 ss is reving high when it is warmed up


First check entire length of throttle cable for kinks, crimping or binding. (especially near steering head) Check function of twist grip, it must rotate smoothly and spring back when released. Ensure choke is turned off after initial warm-up. If no change, turn out idle screw fully,(owner's manual refers) start bike and keep throttle at idle speed and screw in idle screw till it engages.

Apr 17, 2010 | 1992 Ducati 400 SS

Not finding what you are looking for?
2002 Yamaha V Star 1100 Classic Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

D. E. Hev

Level 3 Expert

1187 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...