Question about 2005 Suzuki GSX-R 1000

1 Answer

Fuel pump does not work if I try to start it , but if I send power to it with a power probe it turns.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 192 Answers

The Bike Technicians Tactic

Phase1

An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician's tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities.

Engine Technicians Tactic

PHASE 2

A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.

Posted on Feb 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Bike will turn over but fuel pump not powering up


check the relay and fuse if they are ok check the power coming from the ignition switch make sure it is powering up that circuit if it is check the fuel pump

Feb 16, 2014 | Motorsports

2 Answers

I have a 97 chev suburban 350 and no power to the fuel pump ,new fuel pump,fuel pump relay fuse is new,checked all wiring no cracks or breaks all along from fuse s to pump all good,just when i turn key is...


I would interrogate the fuel pump relay socket with a voltmeter or test light. There should be one hot terminal from the ecm b fuse. There should be a terminal that has chassis ground for the relay coil. The positive terminal for the relay coil comes from the ecm when the key is on. If you have trouble interpreting the results of these troubleshooting steps, feel free to comment back. The circuit is on the right of the diagram about 1/3 down the page.

0996b43f80231a1a-4tnsvvnywbpxz3cmxbpyvis1-5-0.jpg

Sep 28, 2017 | 1997 Chevrolet Suburban

1 Answer

I have a 03 Hyundai accent I just replaced the fuel pump I have no power to the fuel pump I've checked the fuses and the fuel pump relay it won't start I'm not sure what to do next


Do you have a test light? If not, go buy a cheap $5 test light-one with a lead to clip to a ground, and with a needle type probe.
Pull the fuel pump relay out of the terminals it is plugged into-you need to check if the power feed for the pump is still available at the relay. Clip the test light lead to a ground and touch the test probe to the positive battery post-to check that your ground is good- tester should light up. Now touch the probe to all of the terminals that the relay plugs into. One terminal should have power with key off. If no terminals have power, you have lost the power feed for the pump. Double check all your maxi fuses in the power distribution box. Either a maxi fuse or a fusible link will be the power feed for the fuel pump relay.
If the power feed is there at the relay, try a new relay. If still no pump, a shop will probably have to check your fuel pump circuit.
Did you check for power at the fuel tank while the key was held in crank? When the engine is cranking, the fuel pump wire should have power. When the key is turned to on, the fuel pump should have power for about 2 seconds, to pressurize the fuel system. Then when key is turned to crank or start, the fuel pump should stay on.

Sep 07, 2013 | Cars & Trucks

2 Answers

Electrical prblem


There would be a fuel pump fuse, either under dash or under hood. Check that fuse, use the test light to see if fuse has power. If not, then it might be a fusible link or maxi-fuse that feeds the fuse panel. If fuse has power with key on, pull the relay, and use the test light and probe relay terminals, key off. One terminal should be hot at all times. If not, check for power loss between battery and relay terminal-possibly a maxi-fuse or fuse link.
If relay does have power to terminal, quickly check other terminals while someone turns key to on-for about 2 seconds, another terminal should show power-this would be signal from computer to turn the relay on to prime the lines and fuel rail. If you have that, plug relay in and cycle key. Does relay click? If yes, relay is working and problem may be at fuel pump connector. If relay is not working, but you have power to it, and the short signal from computer is there, then check the relay's coil side ground. Computer signals the coil side and the signal goes to ground from relay coil side.
Pull the relay and use a jumper wire from relay's hot terminal to fuel pump terminal-the wire to pump from the relay. If pump comes on, the problem is right there at the relay-either no signal from computer or the relay coil's ground is lost. If pump does not come on, again check connector at pump-that or the wire to pump[ has a problem.

May 12, 2013 | 2001 GMC Savana

2 Answers

My fuel gage is reading full at all times and the radio will not come on is this a fuse issue or two different issues?


You definitely have two different issues as the fuel gauge and radio are on different circuits. The radio could be a blown fuse, which would require finding a short circuit. The fuel gauge could be as simple as a bad connection at the sending unit or a lost ground on the fuel tank. Disconnect the fuel gauge at the tank and with a twelve volt test light well grounded probe the harness terminals with the key on (engine off). The fuel gauge should move when the sending unit wire is probed, and the test light should light dimly. Other terminals are a ground for the sending unit, a ground for the fuel pump, and power for the fuel pump. If the gauge moves when the sending unit wire is probed the problem is either the sending unit or a bad harness connection. If the gauge doesn't move during the probe there is a wiring problem (open circuit) or a bad dash gauge. Hope this helps.

Jul 02, 2011 | 1998 Ford Windstar

6 Answers

No power to fuel pump


when u checked this u do realize the fuel pump only has 12 volts for 1 second then the computer turns it off unless the engine is started? let me know.

Dec 03, 2009 | 1997 Dodge Ram 1500 Club Cab

1 Answer

SENDING UNIT ???????


most of fuel pumps were in tank, wire corrodes is harness under right front seat floor pan to tank
if fuel pump buzz is heard and car runs and when it doesnt run you cant hear the fuel pump try
turn ignition off wait 10 seconds
turn ignition to on position to (prime or hear pump buzz)
no buzz fuel pump not working check fuel pump relay(swap with another) and try again?
you could use test light to pump wiring and make sure your getting power to pump on this prime test no power relay or wiring problem.
power at pump, but no buzz fuel pump faulty

Jul 01, 2009 | 1997 Isuzu Rodeo

4 Answers

Chevy s10 pickup fuel pump does not work


i have a 98 chevy s10 zr2 and we changed the fuel pump and aint gettin no power to the fuel pump checked the fuses and relay under the hood no power and the gauges inside are not working other than lightin up.are there another fuse link some where

Mar 18, 2009 | 1999 Chevrolet S-10 Pickup

3 Answers

1995 Ford Probe sputtering, dying. Won't start now.


This to me sounds like it could be the fuel pump but first I would check the simpler solution and make sure your alternator is good because if your started turns over fine but the car wont start the next part to check would be for me the alternator.

Dec 18, 2008 | 1995 Ford Probe

Not finding what you are looking for?
2005 Suzuki GSX-R 1000 Logo

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5924 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...