I just purchased the vision trimax semi integrated bars. my local lbs called and said the sramm tt500 brakes arent compatible, becuase they are internal routed, and the bars are externally routed. i went down to take a look, and he showed me where there are no holes for the brake cables to exit, he said it could be possible that they forgot to drill the holes. has anyone seen this problem. thanks

there are lots of different shifters out there of different qualities and brands. When replacing a shifter, you should keep in mind that on most modern bikes (bikes built since the 1990's) the shifter is integrated with the chain and rear cogs and they need to be compatible to achieve proper shifting. Without any more details about your set up I recommend going to your LBS (local bike shop) and get their advice. Just as you wouldn't put Ford parts into a Chevy the same holds true of your bike, you need to make sure the parts are compatible and depending on the age of the bike they may no longer be made and you will have to upgrade your parts, this may not be worth the value of the bike overall, thus it is best to consult your LBS.

You can ask me to make a copy for you, but first I have to ask you:
Do you have a Trimax machine in your possession now?

I have a manual for the Trimax exercise machine and can make a copy for you.

All I can say about it is Motor out of the frame. One just have to do a compression test before pulling the motor. Not real good. If not satisfied pour a bit of oil in the sparkplug hole and tested again, almost 130 lbs. Top end time. When the oil will be drained the oil from the frame, the first thing out was several ounces of water.
https://www.structuredsettlement-quotes.com/

Your Felt q520 uses a Semi-Integrated 1 1/8 inch headset. These headsets are known under various names such as zero-stack and low-profile. The cane creek on your old trek is most likely a conventional threadless headset. The standards are not compatible.

Please purchase a semi-integrated 1 1/8 inch headset and have a bike shop install it for you as pressing the cups into and out of the frame requires special tools and if done improperly can destroy the frame.

76lb/ft on the upper and lower nuts

The 48-bit color Visioneer OneTouch 6600 USB scanner delivers outstanding image quality by recognizing over 281 trillion colors at 600x1200 dpi optical resolution. The scanner has three convenient buttons that integrate with the ScanSoft PaperPort Deluxe software to make emailing, copying, and storing images and text effortless. The software bundle also includes ScanSoft TextBridge Pro OCR and MGI PhotoSuite III SE.

The scanner driver is certified by Microsoft for Windows XP, and also is compatible with Windows 98, Windows 2000 and Windows Millennium Edition.

It is not compatible with windows Vista.

most ps3's unfortunately arent backwards compatible, however the 60gb consoles were made to be so. otherwise they can have chips put in them by people while being semi-legal is cheap and works well. so either have the 60gb console, or get a shark chip from your local supplier.

Remove the tail light, then the grey bar with all the lights by removing the two screws at the top and bottom. play with the light socket that dosen't work and chances are that it is cracked and broken. If it is broken then the contacts within are not making contacts becuase the black plastic socket is used to hold the contacts together. If you are handy, you can tear open the grey bar and solder the contacts together, then epoxy the bar back together. Or, find, purchase and replace the grey light socket bar.

raise rear of vechicle then support by jack stands.let rear suspension hang to take pressure off strut coil springs.remove rear package tray trim panel. remove rear wheel.remove brake load sensor .remove brake hose.remove stabilizer bar bracket and link.remove tension strut .remove spindle pinch bolt and strut assembly.if the strut coil spring broke you wont need a coil springcompressor.BESURE INSTALL NEW MOUNTING BOLTS AND PINCH BOLT.install the strut assembly.use a new pinch bolt .torque it to 50-67 ft lbs.torque the 3 upper mounting nuts to 19-25 ft lbs. tension strut torque nut to 35-46 ft lbs. stabilizer bar link torque to 60- 81 inch pounds.stabilizer bar bracket torque to 25-33 ft lbs.NOW INSTALL .brake hose / brake load sensor/ rear wheel /rear package tray trim panel.