I have a yellow warning triangle on the display panel of my F800GS. It is also displaying 'LAMP'. The low beam bulb wasn't working. I have correctly replaced the defective bulb but the display still shows that its defective and the bilb is not working (tried two different bulbs, both brand new) can you help? Is it the fuse? Where is the fuse? Cheers...Derek

This is the master warning light. It is a warning that another light is lit or a condition has occurred that requires review by the driver. If there is a driver information window a message may be displayed.

Example of other conditions depending on the car is:

• Low tire pressure
• low window wash
• Low fuel warning

Hope this helps?

First check light relay fuse, if ok check battery voltage at low beam light terminal, if ok replace low beam bulb, if no voltage check switch side of relay, if voltage replace relay, if no voltage check headlight low beam switch.

seems you have several different problems. High beam working and no low beams=dimmer switch is bad. Reverse lamp not working=bulb socket bad,wiring broke,bad ground at back
Brake light on drivers side stuck on=brake light switch

A yellow triangle with an exclamation point inside of it on a Mitsubishi Outlander Sport usually indicates a warning or caution message. This warning message may be related to a specific system or component in your vehicle, such as the brakes, transmission, or tire pressure.
To find out more about the specific meaning of the yellow triangle warning, you will need to consult your vehicle's owner's manual or refer to the warning message displayed on the dashboard display. The owner's manual should provide more information about the meaning of the warning and any necessary action you should take.
If the warning is related to a specific system or component, it may be necessary to have the issue addressed by a mechanic or service professional. Ignoring a warning message could potentially lead to further problems or damage to your vehicle.
I hope this information is helpful! Let me know if you have any other questions.

It is really confusing when different people have different explanations for this ?? Sign . I had the same warning sign today flashing on My Mitsubishi Outlander 2016 MY17 and I found conflicting explanations on different online forums which was not satisfactory. I even called local and National Mitsubishi customer services and I was told to bring down the vehicle to the service station and they also said that they don’t know what the ?? signs indicates . Pretty bizarre ! Pertinent to mention here that this warning ?? sign states displaying on the panel this morning when I was driving from home to work and I was running low on ?? as low fuel warning started displaying at the same time . Anyway later in the afternoon I went to refuel my car at a nearest petrol station and topped it up and turned on the ignition and the ?? sign was no more displaying on the panel. I also read that this ?? Sign can displaying indicating low tyre pressure or in my case low fuel pressure . I think there is nothing to be worried about unless the ?? Sign keeps displaying .
Thanks

the Blue Lcd panel was broken, the price of the panel is USD80

Have a good day!

We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel,

motherboard, powersupply ... with high quality and competitive price.

Jerry Lampdeng Limited

1. Open the hood.
2. Remove the park/turn signal lamp assembly.
3. Remove the headlamp retainer pins.
4. Pull out the headlamp assembly in order to access the electrical connector.
5. Disconnect the electrical connector.
6. Remove the bulb from the headlamp assembly by twisting the bulb counterclockwise.

INSTALLATION PROCEDURE

IMPORTANT:

• Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
• Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.

1. Install the new bulb to the headlamp assembly by twisting the bulb clockwise in order to lock in place.
2. Connect the electrical connector to the bulb.
3. Install the headlamp assembly.
4. Install the headlamp retainer pins.
5. Rotate and lock the pins in place.
6. Install the park/turn signal lamp assembly.
7. Inspect the operation.

fuse #38 on the inside inside fuse panel was blown on mine, replaced and lights work fine.

hey dude,, just to try n help the easiest way,, on the hi beam lite u will only have two wires on some bikes ,but 3 wires mostly runnin into it,, so 4 an example lets say u got 2 wires,,this being yellow and green if i remeber,,yellow will be hi beam ,,green is low,, the earth would come from the bulb and earth in to the loom,, ,, easiest thing to try,, and by pass hassle,, is on the hi beam lite itl be the yellow wire ie the live on that bulb ,snip it off enuff to be able to join it to the hi beam on the bulb in the head lite, , ,, so u have in your hand say u have the hi beam lite which will have an earth wire black,, leave that connected,, and a yellow wire ,which will be the live in,,snip that wire and touch it on the yellow on the headlite bulb ,, dip the lite and hi beam will go out,,hope that helps

You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.

I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp