Question about 1997 kawasaki ZX-6R Ninja

1 Answer

1997 Kawasaki ZX-6R Ninja carburetor adjustment setting

I need to know the standard settings on a 600 Kawasaki ninja zx6r for carb @

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • kawasaki Master
  • 56,881 Answers

Hi, Terrytingle7 it should be noted that the "AIR FUEL" mixture screw adjustment "ONLY" manages your idle and has no effect on any other circuit also any intake leaks must be repaired before the A/F adjustment procedure can be performed otherwise you will never obtain a proper idle and you will waste a lot of time chasing the impossible. The A/F mixture screw's purpose is to fine tune the fuel charge entering the combustion chamber. The following applies to both 2 and 4 stroke engines:
1. The mixture screw may be sealed at the factory with a Welch Plug please review the following video for removal.
https://www.youtube.com/watch?v=wAXcksgvDkM
2. The mixture screw manages a range of 3 complete 360-degree counterclockwise turns from the bottom/closed position.
3. The mixture screw should have a spring and o-ring for tension and sealing integrity.
4. Turn the mixture screw clockwise until it gently bottoms out, this makes the fuel charge very lean and the engine should not idle if it does then the pilot/idle jet is too big and needs to be replaced with the next size smaller.
5. Turn the mixture screw 1 and 1/2 turns counterclockwise to establish a baseline for starting the engine.
6. To fine-tune the idle circuit, adjust the mixture screw 1/4 turn in or out to achieve maximum idle RPM, wait 15 seconds between each adjustment for the idle to settle.
7. Never go past 3 full turns out this will make the fuel charge rich, foul plugs, and produce black smoke out of the exhaust, if the engine RPM keeps increasing past 3 turns the pilot/idle jet is too small and needs to be replaced with the next size larger.
8. After achieving maximum idle back out the mixture screw another 1/8 of a turn then adjust the throttle cable idle stop screw to 950-1050 RPM.
9. This procedure works great on 99% of all engines, for the 1% that demand a more robust throttle response on aftermarket monster fuel delivery systems additional tweaking outside the box may be necessary.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1998 ZX6R Stock Carb Settings KawiForums Kawasaki Motorcycle Forums
http://www.zxforums.com/forums/mechanical-technical/37527-setting-mixture-screws.html
Kawasaki 1985 ZX600 Service And Repair Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on Mar 24, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
cape cod bob
  • 292 Answers

SOURCE: i want the suspension settings for a 2001 j2

you want what kind of suspension settings?

suspension front and rear are both tunable to riders weight and riding style. if you think it's too soft, stiffen it up and vise vesa

Posted on Mar 31, 2009

  • 132 Answers

SOURCE: I want to chang the horn in my kawasiki ninja zx6r

the horn is only held on by 1 bolt,undo this and remove the 2 wires then just reverse these steps to refit

Posted on Jun 13, 2009

  • 3567 Answers

SOURCE: need to remove the cam chain on my kawasaki zx6r

Cam chain replacement is a bit complex for a beginner. I don't recommend it. However, I would suggest the best way is to have a service manual at hand. Go to this site and you can download a free PDF service manual.www.carlsalter.com/motorcycle-manuals.asp

The 2005 manual (4th from the bottom), is 11MB. You can go with the '05 manual as the service proceedure is the same as the 1998. The 2002 manual is 80 MB (scanned differently).

70adb57.gif

Go to the site below where you can see a parts diagram for your specific bike. You will select the actual brand, year, model, etc., once you go to the site. Part numbers and prices are also shown. You can order parts from this site. In the event no price is shown on a particular part and/or the notation "Not Available" is in the description, the part is not in stock. www.babbittsonline.com/pages/parts/viewbybrandand/parts.aspx

Can I get a “very helpful” rating on this answer?

Posted on Aug 14, 2009

  • 80 Answers

SOURCE: where is the engine number

your engine is located behind the faring and below the fuel tank.Thank you.

Posted on Oct 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Kawasaki ZX-6R Ninja dies with throttle


Hi, Anonymous and the usual suspects are:
1. Idle port, transfer ports, slow air jet clogged.
2. Idle adjusting screw set too low.
3. Air fuel mixture adjustment too lean.
4. Pilot/slow fuel jet clogged.
5. Faulty accelerator pump.
6. Float level too low.
7. Float bowl contaminated old fuel, water, dirt, rust, etc.
8. Carburetor bowl vent line clogged/blocked/pinched.
9. Fuel line to carburetor kinked or pinched.
10. Fuel filter clogged.
11. Intake manifold leak.
12. The gas cap is not venting properly or fuel tank venting system blocked.
13. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
14. Needle and seat stuck closed in the float bowl.
15. Multi carburetors not in sync.
16. Faulty fuel pump or internal fuel line has pinholes.
17. Fuel injectors clogged or faulty.
18. Faulty throttle position sensor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Ninja starts but dies when open the throttle
http://www.newninja.com/forums/f161/zx-6r-starts-fine-but-dies-when-throttle-is-applied-16041.html
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 18, 2014 | 2000 kawasaki ZX-6R Ninja

1 Answer

1997 Kawasaki ZX-6R Ninja how to install the speedometer cable


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Speedometer Cable install ZX Forums
How to fix speedometer cable on motorcycle kawasaki ninja 250 Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Apr 22, 2014 | 1997 kawasaki ZX-6R Ninja

1 Answer

1997 Kawasaki ZX-6R Ninja will not idle


Hi, Anonymous and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
97 ZX6R Turns over but won hold idle
http://www.zxforums.com/forums/mechanical-technical/40220-2000-zx6r-wont-stay-running-stuck.html
Kawasaki 1985 ZX600 Service And Repair Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 26, 2013 | 1997 kawasaki ZX-6R Ninja

1 Answer

1997 Kawasaki ZX-6R Ninja service manual


Hi, Anonymous the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual
Kawasaki ZX6R Ninja Specs ZX6R Ninja info ZX 6R Ninja specifications
Kawasaki Ninja ZX 6R

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 23, 2013 | 1997 kawasaki ZX-6R Ninja

1 Answer

2001 Kawasaki ZX-6R Ninja how to tighten the chain


Hi, Timothy for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.zxforums.com/forums/zx-6r-forum/22912-chain-adjustment.html
How to adjust 20013 16 zx6r chain
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Mar 27, 2013 | 2001 kawasaki ZX-6R Ninja

1 Answer

1999 Kawasaki ZX-6R Ninja engine oil capacity


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Parts Specifications KAWASAKI ZX 6R NINJA Louis Moto
Changing the Oil Filter of Motorcycle Kawasaki Ninja 636 ZX6R
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Jul 07, 2012 | 1999 kawasaki ZX-6R Ninja

1 Answer

2001 Kawasaki ZX-6R Ninja how to bleed a fuel line


Hi, Anonymous for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bleed Out the Air
Sputtering Dirty Carburetor Fix Easy Way Ninja 250
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


May 06, 2012 | 2001 kawasaki ZX-6R Ninja

1 Answer

2001 Kawasaki ZX-6R Ninja how to set the timing


Hi, Jasminhr for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
timing on zx6r please asap KawiForums Kawasaki Motorcycle Forums
2005 Kawasaki ZX 6R Timing Chain Overview
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Jul 13, 2011 | 2001 kawasaki ZX-6R Ninja

1 Answer

1997 Kawasaki ZX-6R Ninja fuel and vacuum line routing


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1997 Kawasaki ZX 6R Ninja fuel and vacuum line routing Google Search
about vac and fuel lines 95 zx6r
Kawasaki 1985 ZX600 Service And Repair Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 12, 2010 | 1997 kawasaki ZX-6R Ninja

1 Answer

1999 Kawasaki ZX-6R Ninja suspension sag settings


Hi, James_k400 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Suspension Setup Guide ZX6R Forum
Suspension Settings KawiForums Kawasaki Motorcycle Forums
1998 1999 Kawasaki Ninja ZX 6R ZX600 Service Repair Factory Manual INSTANT... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Dec 27, 2009 | 1999 kawasaki ZX-6R Ninja

Not finding what you are looking for?
1997 kawasaki ZX-6R Ninja Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5880 Answers

Marvin
Marvin

Level 3 Expert

85020 Answers

richard libby

Level 2 Expert

208 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...