2003 Yamaha YZ 125 Logo
Posted on Sep 28, 2010
Answered

How are the basic setting in the carburator? - 2003 Yamaha YZ 125

Answer This Question

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.
MVP:

An expert that got 5 achievements.
New Friend:

An expert that has 1 follower.
Hot-Shot:

An expert who has answered 20 questions.

  • Contributor 32 Answers
  • Posted on Sep 29, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
MVP:

An expert that got 5 achievements.
New Friend:

An expert that has 1 follower.
Hot-Shot:

An expert who has answered 20 questions.

Joined: Sep 23, 2010
Answers
32
Questions
0
Helped
11597
Points
87

You have a mikuni carb. there are curcuits to the carb. the first that works from idle to 1/4 throttle is the pilot cicuit, from there you transition to the needle jet/and jet needle. That controls the 1/4 to 3/4 throttle and then the main' jet which controls WOT. you may have a air screw that would be before the throttle plate if it is after it is a fuel screw find the factory specs for the jet sizes and make sure all is correct. if not you isolate where the problem is and correct in a rich or lean adjustment' I race yamaha 2 stroke road racing bikes, it is not an easy task sorry to complicate you so much

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What is basic carburator settings.
start with 1,5 turns out from the fully seated position. Then fine tune the High and Low
http://www.aerocorsair.com/id150.htm
Read full answer
Jun 10, 2014 • Poulan Garden
1helpful
3answers

Carburator and idle problem
Believe it or not you just said the solution to your own problem manufacturers specs requires for any adjustments to engine idle or other carburator adjustments to be preformed while the engine is idling and at normal operating temp in plain english let the car warm up then make your idle and mixture adjustments if this doesnt solve it i would check the auto choke and make sure it is opening at normal operating temp hope this helps good luck
Read full answer
Sep 01, 2008 • 1984 Toyota Tercel
0answers

HOW TO ADJUST CARBURATOR FOR BETTER MILEGE
Read full answer
Be the first to answer Jan 24, 2014 • 2006 Bajaj Wave
0helpful
1answer

Hi i have a 4stroke 125cc pit bike it wont start tried bump start sorted turned over but when i reved it didnt respond then died any ideas
Tryd go to auto shop and check the carburator of your motor and clean your air filter adjust air setting in carburator and put a new fuel pump check fuel setting in carburator
Read full answer
Jan 18, 2014 • Motorcycles
0helpful
1answer

Need carburator adjustments high and low mac 3516
Basic settings one and a half turns out on both screws, you will need to fine tune from there.
Read full answer
Feb 15, 2011 • McCulloch 16 Inch Gas Chain Saw MCC1635AK
1helpful
1answer

How do you set the carburator back to factory specs. mine wont keep running
Basic settings can vary from model to model, a good starting point for most carbs is screw both H and L screw right in ,then back the H screw out 1 turn and the L screw 1 and1/4 turns, the machine should run well enough to fine adjust from there, they are both fuel screws, so the more you unscrew them the richer the saw becomes, always remember if there in another under lying problem adjusting the carb screws will not always help, before any adjustment clean or replace the fuel filter in the fuel tank.
Read full answer
Feb 03, 2011 • McCulloch 16 Inch Gas Chain Saw MCC1635AK
0helpful
1answer

Truck is skipping,cutting back and back firing out the Exhaust is this caused by the carburator
carb can cause alot of head aches but first check basics plugs wires cap rotor i think the ignition timing is out check ignition timing incl is a chart with engine specs set base timing then rev engine up to 1500rpm an timing should advance 110-15 degrees if distributor4 advance is working make sure there is vaccume to distributor advance hope this helps if not let us know the results
shinehutt_16.gif

shinehutt_15.gif
Read full answer
Jan 12, 2011 • 1987 Toyota Pickup
5helpful
1answer

Air fuel mixture setting for Ryobi 31cc engine. I changed out all the fuel lines because the old ones were dry rotted. After changing them out them out my engine will not stay running. I can see air mixed...
Make sure your lines have been hooked up correctly. Take a look at the sketch and see if yours looks like this. d0e1722.jpg
Read full answer
Apr 29, 2010 • Ryobi Garden
1helpful
1answer

Weedeater carburator setting on bolens 31cc
initial setting is 1and1/4 turns out for walbro carb.
1 turn out zama carb.
Read full answer
May 26, 2009 • Garden
2helpful
2answers

New carburator and it runs worse
Check your fuel pump,it sounds as if you have excessive fuel pressure.
Read full answer
May 05, 2009 • 1984 Ford F 250
Not finding what you are looking for?

View Most Popular

2003 YZ 125

  • Motorcycles

Related Question

What is basic carburator settings.

  • Poulan Garden

Related Topics

664 views

Ask a Question

Usually answered in minutes!

Popular Questions

Find a free Owner's manual for yamaha yz125

2004 Yamaha YZ 125

A lot of gas coming out of the carb. overflow tube, eng on or off

Yamaha YZ 125 Motorcycles

Leaking oil from power valve on 2000 yz 125

2004 Yamaha YZ 125

Yamaha YZ125 Clutch not disengaging

2003 Yamaha YZ 125

What are the specs for fork oil in a 99 YZ 125

Yamaha YZ 125 Motorcycles

Top Yamaha Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

littlewheel

Level 2 Expert

122 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...