Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van

It has a Data Link Adapter. Right side of steering wheel. It is not a traditional OBD Port.

https://www.google.com/search?q=diagnostic+port+on+my+1993+mercury+villager+van

..

Engine compartment main fuse panel 30 AMP fuse Fuse #4 scroll down and look at this diagram picture on this link. http://www.autogenius.info/mercury-villager-1st-generation-1993-1998-fuse-box-diagram/ caution, this fuse runs power seats, windows and sun roof as well.

Mercury Villager 1st Generation 1993 1998 fuse box diagram Auto Genius

1995 Mercury Truck Villager Van 3.0L EFI SOHC 6cyl

The Crankshaft Position Sensor is located: Under hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block.

The alternator is not charging the battery. Could be a bad connection bugt usually it's the alternator that's bad. The Villager & Quest both turn on the battery light and the brake light when the charging system is not working porperly

I have a 2002 villager estate I just got, and the power seat on the dirvers side will not work, along with the power mirrors. I think it is related to the memory seats, since that controls both. Has anyone else had this problem. Also, the fan on the A/C only works on 4 and the other switch for where the air comes out doesn\'t work. Anyone else? the drivers window switch only puts the window up if you pull really hard on it.

that engine is built by nissan believe it or not. look on the net for your van or a nissan maxama. I just googled it and found lots of diagrams for that van(95 mercury villiger 3.0 timing belt diagram. I would not only replace the belt, I would replace it using a timing belt replacement kit.If your going to keep the van.

there is a groups.yahoo.com/villager-quest owner group for help

no switch in van. Spray with penetratingoil & see if it loosens up.

Fixed back glass or does glass open? Handle on back glass?

Go here

http://groups.yahoo.com/group/villagerquest/

door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   

1. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
   
   
   
   
   

1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
   

1. Pull the shop rag back and forth to release the window regulator handle clip.
   
   
   
   
   

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screw from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
   

1. Remove the front door trim panel.
   

Installation
To install, reverse the removal procedure. Body Side
Removal

1. Gently pry loose the body side door latch handle bezel and remove it.
   

1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).
   
   
   
   
   

Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal

1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
   

1. Remove the front door watershield by carefully detaching it from the adhesive.
   

Installation

1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
   

1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.
   

This is easy. Lift the lid open. Look at the back of the sealed beam and you will see a clip and an o ring. Pull the clip up and pull wires back toward the driver's seat. Unscrew the o ring and firmly pull the bulb out toward the driver again. Note the 3 tabs on the bulb seat and realign the new bulb with those tab ( 2 bottom, 1 top). Replace with #9007 bulbs..do them both.