Question about 2012 Kymco Super 8 50 2T

1 Answer

Can I bypass an ecu box or an ignition igniter module and sure what to call it on a kymco super 8 or can I replace it with a cdi box or can I get one off Suzuki

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Kymco Master
  • 58,369 Answers

Hi, Todd parts swapping is common with most motorcycles when it comes to interchangeable or compatible parts from one model with another "EXCEPT" for the CDI's they are year-make-model "SPECIFIC" the best thing to do is call your local Dealership Parts Department or a reputable independent shop. If your location is not near a shop then go online and find a parts catalogue or "FICHE" and match part numbers depending on your criteria.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.youtube.com/watch?v=0ZR0FX1_icg
https://www.buggydepot.com/tech-center/gy6-150cc-ignition-troubleshooting-guide-no-spark/
https://www.manualslib.com/manual/1110481/Kymco-Super8-50-2t.html
http://kymcopartsonline.com/catalog/
https://www.kymcousa.com/admin/dealeronly/ownerman/onroad/Super8.pdf

Posted on Sep 23, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: WHERE IS THE ECU IN 1994 LINCOLN TOWN CAR

it is in firewall on left side close to master cylinder

Posted on Dec 12, 2008

tellme2
  • 137 Answers

SOURCE: need cdi wiring diagram for suzuki 900

hi m8,,give these guys a try,, www.repairmanual.com

Posted on May 03, 2009

  • 7 Answers

SOURCE: replace dcs gas cooktop re-ignition module

donho1,

most likely the problem is the switch places onto the shaft of the valve. to replace the switch, you would need to remove the burner cap and port rings. you will see a large brass nut that needs to be removed on all 4 or 5 burners. next you would need to remove the nut in the center of the simmer port ring which is also the venturi for the main burner. you must be careful when removing this nut as they have a tendancy to lock onto the jet holder and could be hard to remove (don't strip or break the venturi or holder).....after you remove those nuts, the burners and top can be removed (watch the igniter wires). you can remove the switch by removing the retainer clip that holds the switch onto the valvestem.

Posted on May 28, 2009

  • 221 Answers

SOURCE: 1980 gs 550 l no spark ..I was told to relace ignition module

yes

Posted on Jul 24, 2009

  • 1 Answer

SOURCE: My 95 Mercury Sable won't start I am getting spark

My 95 mercury sable drives a while then splutters and dies. after it sits a while it starts. It only seems to do this whem its hot outside and has run a while

Posted on Jun 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 Honda CB 250 Nighthawk no spark


Hi, Chance and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Open-short-ground in the wiring between the alternator to the ignition module/CDI box to the ignition coil.
5. Faulty pins or sockets in the plug connectors.
6. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
7. Faulty ignition coil or electronic control module/CDI box.
8. Faulty pulse coil.
9. Faulty CKP, CMP, or BAS sensor.
10. Faulty ignition switch.
11. Faulty run/off switch
12. Tilt sensor needs a reset.
13. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1993 Nighthawk 250 has no spark Honda Rebel Forum
1995 Honda CB250 Nighthawk lost spark help
Honda CB250 Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda CB250 Nighthawk Owner Manual

Sep 16, 2018 | 1995 Honda CB 250 Nighthawk

1 Answer

2006 Kymco ZX 50 will not start


Hi, John and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
17. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
18. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
19. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
20. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
21. Faulty neutral, clutch, kickstand safety switch.
22. Faulty fuel pump or fuse or relay.
23. Faulty or corroded run/stop switch.
24. Tilt sensor needs a reset.
25. Security system not disarming alarm needs a reset.
26. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
Fix Chinese 49cc Scooter that won start
KYMCO ZX SCOUT 50 Service Manual
Kymco Motorcycle Parts
KYMCO ZX 50 User Manual

Jun 28, 2018 | 2006 Kymco ZX 50

1 Answer

Kymco people march 2009 49cc no spark


Hi, Edwin and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Tilt sensor needs a reset.
11. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
No Spark
GY6 Electrical Troubleshooting Tutorial No Spark Eliminator
KYMCO PEOPLE 125 Service Manual
Kymco Scooter Parts ATVs Scooter Parts Performance Scooter Parts...
KYMCO PEOPLE 50 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Sep 06, 2017 | 2006 Kymco People S 50

1 Answer

2009 Kymco People s50 4t will not start


Hi, Jennifer and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
14. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
15. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
16. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
17. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
18. Faulty neutral, clutch lever, or kickstand safety switch.
19. Faulty fuel pump or fuse or relay.
20. A stuck bent or burnt valve.
21. Tilt sensor needs a reset.
22. Security system not disarming alarm needs a reset.
23. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Troubleshooting
Scooter Troubleshooting Scooter won start All about Scooters
KYMCO PEOPLE 125 Service Manual 50cc also
Kymco PEOPLE Parts
KYMCO PEOPLE 50 2005 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 25, 2017 | 2009 Kymco People S 50

2 Answers

Kymco quannon 125cc wiring loom i need help with a very basic diagram showing only the wiring required to get motor running its in gokart the diagram i have dont understand please can anyone help me ?


Hello P Smurf,

Well... don't feel bad...!!
The KIMCO drawing is TRASH (in my humble opinion).

Just start the engine!
- ignition switch on (powers on CDI module)
- short B+ 12V to "S" lead (small terminal on solenoid switch = cranking motor (until it starts (or within reason... do not burn out starter)).

Really... you can short BATTERY to the starter solenoid... as long as you have the ignition on... It SHOULD RUN (if it can).

You only have the REAL two issues you need to start...
Fire & fuel... (everything else is mere confusion).

IGNORE IT ALL... until you get the engine started...!!

I've been reading schematics, circuit drawings, operational diagrams... All of it for more than my adult life... (mere seconds away from 70) amateur radio, patent holder & highly skilled professional... (into full spectrum optics)....

I pulled up the appropriate Kymco "drawing"... and while I'll say it is very pretty (colorful) it is also TOTALLY USELESS...!!
(top reference below... avoid it!).

Whom-so-ever (clown who posted it) that put it together
didn't (still doesn't) know their posterior from 75 cents
(six bits).
I can't even tell if the generator & starter are one-in-the-same
(which would be the first place you want to go...

Useable VERSION immediately below...


Quite Useless:
http://www.enmoto.com/enmotoonline/downloads/Specifications/Kymco/Schaltplaene/Quannon.pdf

I found another source... that has the COMPLETE information:
http://binatani.com/wp-content/uploads/2013/02/wiring-diagram-Kymco-Super8-125cc-engine.jpg http://binatani.com/wp-content/uploads/2013/02/wiring-diagram-Kymco-Super8-125cc-engine.jpg

If you don't have a spark tester just have a friend pull the HIGH-VOLTAGE wire loose enough to see the spark jump...

Else find the CDI Module/Coil... & replace it
(better to get a SPARK test tool...)...
I'm just saying

Comment me back... every tractor & tiller in the world has the same starter circuit
(some just have points & coils in lieu of CDI Modules).

I'll be here!!

Jun 05, 2016 | Kymco Motorcycles

1 Answer

Already replaced cdi box still no go also bypassed the kill switch


Hi, Brian and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
8. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
10. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2 and/or BAS).
11. Security alarm needs a reset.
Good luck and have a nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Aug 24, 2015 | Motorcycles

1 Answer

2007 kymco grandvista won't start after I just had it running shortly, any reason why?


How many kilometers has it done? Either one of these is the culprit; battery, spark plug, ignition coil, or CDI. CDI normally seems to go around 25000-30000kms.

Jun 19, 2015 | Kymco Motorcycles

1 Answer

2006 Suzuki GSX 600 F (Katana) no spark


Hi, Mick and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Open-short-ground in the wiring between the alternator to the ignition module/CDI box to the ignition coil.
5. Faulty pins or sockets in the plug connectors.
6. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
7. Faulty ignition coil or electronic control module/CDI box.
8. Faulty pulse coil.
9. Faulty CKP, CMP, or BAS sensor.
10. Faulty ignition switch.
11. Faulty run/off switch
12. Tilt sensor needs a reset.
13. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1990 Katana GSX600F no spark won run
How to diagnose no spark situation on motorcycle
Suzuki GSXF600 Katana Complete Workshop Service Repair Manual 1998 1999... $20
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals

Oct 05, 2013 | 2006 Suzuki GSX 600 F (Katana)

1 Answer

My kymco super 8 headlights go out when you open the trottle and come back on when the bike is idling


There are three possible sources of power. 1. The light control assay is a module that determines when to cut power to the lights when at idle or starting the engine... it can fail and prevent power from going to the lights. 2. The CDI. It sends a signal to the Light Control Module... if no signal, no lights. 3. The light switch. The wires can get lose and prevent power from going to the LCM. Start at the Switches. Test for power from the switch, if no power from the switch, make sure power is going to the switch. Flip the switch from low to hi beam too, test both lines. The CDI is a bit trickier to test but there is a wire to the LCM that can be powered when the bike is running (a bad CDI is diagnosed after everything else though as it is difficult to test and very unusual to happen). If power is going to the LCM, that rules out the switches. If you confirm power to the LCM, and power from the CDI (a signal from it at least), then its a bad LCM. But check your light bulbs before doing anything. If you bypass the LCM on an American bike (connecting the blue wire to the LCM to the blue wire from the LCM together), it will blow the fuse but some European and Phillipine models work without the LCM. LCM's and CDI's aren't cheap so have a professional confirm the parts are bad before replacing.

Nov 16, 2012 | 2008 Kymco Super 8

1 Answer

Tgb 101S - no spark


did you try another plug maybe the plug is dead or check fuses there might be a blown fuse or a burnt fusable link

Jun 14, 2009 | 2005 Kymco Stryker 125

Not finding what you are looking for?
2012 Kymco Super 8 50 2T Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5944 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...