Question about Suzuki Motorcycles

1 Answer

2001 suzuki vz800 will crank but when i hit the gas it will die

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I’d guess the gas is bad first, either old or there’s water condensation in the tank. Drain it, you may to drop the bowl off the carburetor and clean it.

Posted on Sep 16, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: how does the tank come off on a 2001 suzuki vz800 marauder

first take off the seat
when the front seat is removed you will clearly see 2 10 mm bolts holding down the tank...
you must also disconnect the fuel lines at the fuel shut off switch, i plug them with golf tees
perfect fit.

Posted on May 15, 2009

rogrrabbit
  • 986 Answers

SOURCE: where can i find a second hand crank for suzuki

www.Everdrive.com Here is a site that sells used parts

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: I need a starter for a suzuki VZ800 Marauder 2001.

I have a 1997 parts bike with a good starter. Are youy still looking?

Posted on Jul 08, 2010

dmsr63
  • 2050 Answers

SOURCE: Gas leake from Air vent

If you mean that fuel runs out of one of the vent lines, note that one of those lines is for overflow from the carb bowl. If this is what is happening, you might have corrosion or dirt making your float needle stick, and overflow fuel to that carb. It needs to be cleaned out by removing the bowl, float and float needle.

Posted on Sep 06, 2010

mark24354
  • 776 Answers

SOURCE: My 2001 suzuki vz800 marauder

Make sure the choke is off

Posted on Jul 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Suzuki VZ 800 Marauder clutch slipping


Hi, Richard and the usual suspects are:
1. Clutch controls improperly adjusted.
2. Insufficient clutch spring tension.
3. Friction discs or steel discs are worn or warped past specs.
4. New wet clutch plates were not pre-soaked for 24 hours.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Clutch Slipping 04 Marauder VZ800 Page 2
Suzuki Marauder 800 Clutch Replacement Part 2 Clutch Disassembly
Suzuki VZ800 Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Sep 14, 2018 | 1998 Suzuki VZ 800 Marauder

1 Answer

1997 Suzuki VZ 800 Marauder clutch slipping


Hi, Richard and the usual suspects are:
1. Clutch controls improperly adjusted.
2. Insufficient clutch spring tension.
3. Friction discs or steel discs are worn or warped past specs.
4. New wet clutch plates were not pre-soaked for 24 hours.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Clutch Slipping 04 Marauder VZ800 Page 2
Suzuki Marauder 800 Clutch Replacement Part 2 Clutch Disassembly
Suzuki VZ800 Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Sep 14, 2018 | 1998 Suzuki VZ 800 Marauder

1 Answer

2001 Suzuki VZ 800 Marauder wiring diagram


Hi, Greg nice name, for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2001 Suzuki VZ800 Marauder wiring diagram Google Search
Suzuki Motorcycle Wiring Diagrams
Suzuki VZ800 Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Mar 13, 2018 | 2001 Suzuki VZ 800 Marauder

1 Answer

2001 Suzuki VZ 800 Marauder wiring diagram


Hi, Greg nice name, for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2001 Suzuki VZ800 Marauder wiring diagram Google Search
Suzuki Motorcycle Wiring Diagrams
Suzuki VZ800 Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Mar 13, 2018 | 2001 Suzuki VZ 800 Marauder

1 Answer

1998 Suzuki VZ 800 Marauder running on one cylinder


Hi, Michelle you need "FIVE" things in order for a cylinder to run properly:
1. FUEL: in order to validate your not getting fuel spray some starting fluid into the air cleaner and hit the starter button, if it fires up and runs for a few seconds then you know you have a fuel delivery issue. Multi carb banks should be bench "SYNC"
2. SPARK: remove the spark plug and with it connected to the spark plug cable ground the threads to something metal you should see a bluish white spark if not you have a faulty spark plug, spark plug cable, ignition coil, condenser, CKP, ECM, sensor or the wiring in between.
3. COMPRESSION: you must have at least 80-100 PSI for most bikes, multi-cylinder engines should be within 10-15% of each other if not perform a leak down test you may have a burnt or bent valve or hole in the piston or broken rings.
4. CAM TIMING: confirm your timing marks are aligned to see if the cam chain or adjuster are worn out and the chain has skipped a couple teeth.
5. IGNITION TIMING: on older bikes check to see if your points have not closed up, timing plate has not become loose and confirm with a timing light for proper retard and advance functions, on newer bikes where timing is controlled by an ECM and is nonadjustable check you CKP, TPS, MAP, O2, sensor or its counterpart for integrity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
mis firing VZ800
Vz800 97 only runs on one cylinder possible broken wire
2000 VZ800 marauder 800 Front cylinder not getting fuel
Suzuki 1997 VZ800 Service Manual
OEM parts for Suzuki
http://mybikemanuals.com/suzuki

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Aug 12, 2017 | 1998 Suzuki VZ 800 Marauder

1 Answer

1998 Suzuki VZ 800 Marauder running on one cylinder


Hi, Michelle you need "FIVE" things in order for a cylinder to run properly:
1. FUEL: in order to validate your not getting fuel spray some starting fluid into the air cleaner and hit the starter button, if it fires up and runs for a few seconds then you know you have a fuel delivery issue. Multi carb banks should be bench "SYNC"
2. SPARK: remove the spark plug and with it connected to the spark plug cable ground the threads to something metal you should see a bluish white spark if not you have a faulty spark plug, spark plug cable, ignition coil, condenser, CKP, ECM, sensor or the wiring in between.
3. COMPRESSION: you must have at least 80-100 PSI for most bikes, multi-cylinder engines should be within 10-15% of each other if not perform a leak down test you may have a burnt or bent valve or hole in the piston or broken rings.
4. CAM TIMING: confirm your timing marks are aligned to see if the cam chain or adjuster are worn out and the chain has skipped a couple teeth.
5. IGNITION TIMING: on older bikes check to see if your points have not closed up, timing plate has not become loose and confirm with a timing light for proper retard and advance functions, on newer bikes where timing is controlled by an ECM and is nonadjustable check you CKP, TPS, MAP, O2, sensor or its counterpart for integrity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
mis firing VZ800
Vz800 97 only runs on one cylinder possible broken wire
2000 VZ800 marauder 800 Front cylinder not getting fuel
Suzuki 1997 VZ800 Service Manual
OEM parts for Suzuki
http://mybikemanuals.com/suzuki

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Aug 12, 2017 | 1998 Suzuki VZ 800 Marauder

1 Answer

My 2001 vz800 dies occasionally when i pull in the clutch


possibly, it might be the kickstand safety switch is sticking!

Jul 26, 2013 | 2001 Suzuki VZ 800 Marauder

1 Answer

My 2001 vz800 dies occasionally when i pull in the clutch


possibly, it might be the kickstand safety switch is sticking!

Jul 26, 2013 | 2001 Suzuki VZ 800 Marauder

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5944 Answers

ROB

Level 3 Expert

858 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...