Question about Motorcycles

1 Answer

Hi i have the lg exalt vn220 and i would like to shut off the kill switch how do i do that thank you

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 58 Answers

Not sure I understand your question. If you mean bypass the kill switch, simply unplug it and connect the two wires together.

Posted on May 02, 2019

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I enable the kill switch on my lg15gb


What is the make, model and year of vehicle. This is the car and truck forum.

Apr 27, 2016 | Cars & Trucks

1 Answer

How can I shut off the motor? Is there a kill switch?


there is supposed to be a kill switch on side of engine. just follow the cable down to engine. it may be broke or just frozen. the cable that shuts down mower. Good-Day!

Jun 07, 2014 | Garden

1 Answer

Triumph tiger 955i radiator fan doesnot shut off


Hi, Check that temp switch. replace if nescessary. If the engine is running too hot change the thermostat for a colder one. Good luck.

Mar 15, 2012 | Triumph Tiger Motorcycles

1 Answer

My Makita DCS520i chainsaw will not shut off. I replaced the kill switch and that did not work. The wire and connections look fine. I assume the ignition coil is ok since it starts fine. Anyone know what...


Hi,

OK. The kill switch breaks the circuit to the plug. Since you replaced the kill switch, assuming it is good (did you test it with a multimeter?), the problem has to be in the wiring to the plug from the switch. If the plug gets power all the time, then the circuit is complete all the time.
I'd replace the wires from the switch to the plug.

Hope this helps. If it does, I'd appreciate a 4 thumbs up. Thanks,

Handie Andie

Apr 26, 2011 | Makita Garden

1 Answer

Hi, i just purchased two LG LCD TV's the 26LD350 and the 32LD350 I'm worried that it does not have an off switch and only goes on to standby mode. you here alot about tv"s catching on fire because of this....


I have never heard of any LG TVs having a fire issue.
LG added this switch to help save electricity. "Going Green".
You see, this On/Off switch was added to kill the power to the TV when not in use. This switch stops the TV from consuming power by not giving it power to be in a “Stand-By” mode.
If your TV does not have this switch, you could simply unplug your TV to give you the added satisfaction it won’t catch fire.
I hope this information has helped.
Good Luck.

May 23, 2010 | LG Televison & Video

2 Answers

Bike shut off on the freeway and wont start again.


Got gas? Got water in the gas? Drain the carbs and fuel line.

Check for spark. If no spark then check again with a new plug.
Is the kill switch on? Does the side stand have a kill switch? Is it working properly? Tip-over kill switch on your bike? Check the operation of the ignition switch and all kill switches with a volt ohmmeter.
Are all wires clean and with a solid connections? Check the loom. Any abraded wires? Is the bike in neutral and the neutral light is lit up? If no neutral light, check the neutral switch and neutral switch wire on center casing. With a little luck this will get you back on the road.

Please rate this solution. Thanks!

Apr 05, 2009 | 1995 kawasaki ZX-6R Ninja

1 Answer

Replaced stop switch and it still won't shut off!


While attending college, I worked at a tool rental center and learned many tips and tricks from the mechanics. The problem that we heard the most from customers was that the machine would not start. Your your machine at least starts and runs fine, however will not shut down with the factory kill switch. Many times when replacing the mag. (spark coil) the kill wire would rub against the flywheel and break or over time the conductor wire will break inside the insulation. If you kill switch only has one wire, then all the kill switch does is short the mag to ground. Simple test is to remove spark plug, re-connect wire to plug, touch plug to engine and pull rope to observe spark, then short the tab on the magnito to ground, should be no spark. If you still have spark, coil is defective however good enough to run engine. Kill with choke or pull wire. If no spark with test, make new wire from tab of coil to kill switch or any switch that will short tab to ground. Good Luck

Jan 03, 2009 | Briggs Garden

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5948 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

1400Slugg

Level 2 Expert

260 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...