Installing allmy harnesses - Cars & Trucks

car audio installation products This will solve your problem.

About 3,970 results (0.89 seconds) Search Results

Ford Bluetooth® Wiring Harness - Crutchfield

www.crutchfield.com/.../Ford-Bluetooth-Wiring-...

Crutchfield Corporation
Rating: 4.5 - ‎16 reviews - ‎$19.99 - ‎In stock
Reinstall the factory radio and mount the Bluetooth kit, and you're ready to go. ... 16Reviews ... harness so that I could hook up an aftermarket amp to my factory radio.... works like it's suppose to. says it doesn't work on an 09 Escape but had no .... I purchased this harness to install a parrot ck3100 in my 07 Ford Edge.Missing: pwm

70-5521 wiring harness for ford with 6 CD premium sub amp ...

? 4:30
https://www.youtube.com/watch?v=0jqNafnki0o
Aug 9, 2013 - Uploaded by codieraji
Metra 70-5521 Radio Wiring Harness for Ford 03-Up Amp FordPremium stereo radio 6 CD changer with sub amp inputs. ...16:47. How to wire an aftermarket radio / I Demo install with metra harness and antenna ... How to hook up stock amp/sub to aftermarket head unit "ford sport trac" - Duration: 3:01. Pat.Missing: parakeet ‎pwm ‎98

Car Stereo Wire Harnesses - Radio Wires for all Car Audio ...

www.installer.com/main.php?page=harness
Car Stereo Wire Harnesses - Car Stereo Installation Wiring - Stereo Harness ... If you

Make sure the ground wire isn't damaged. If it isn't earthed correctly, you won't get power!

Remove the accessory drive belt. Disconnect the negative battery cable. Disconnect the generator electrical connector. Remove the engine harness terminal from the generator: - Slide the boot back along the cable. - Remove the engine harness cable nut (3). - Remove the engine harness terminal from the stud. Remove the generator bolts and generator. Install the generator. Install the generator bolts. Tighten the generator bolts to 50 N?m (37 lb ft). Install the engine harness terminal to the generator: - Install the engine harness terminal to the stud. - Install the engine harness cable nut (3). Tighten Tighten the engine harness cable nut to 13 N?m (10 lb ft). - Slide the boot over the generator stud. Connect the generator electrical connector (1). Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure . Install the accessory drive belt

Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

1. Verify that the multifunction turn signal lever is in the center of the OFF position.
2. Disconnect the negative battery cable.
3. Disable the SIR system.
4. Remove the steering wheel.
5. Remove the steering column trim cover.
6. Remove the steering column knee bolster.
7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
8. Remove the 2 wire harness straps from the steering column wire harness (1).
9. Remove the steering column bulkhead connector from the vehicle wire harness.
10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.

1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
2. Remove the multifunction turn signal lever (2) from the steering column.

Installation Procedure

1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
2. Verify that the electrical contact rests on the canceling cam.

Notice: Refer to Fastener Notice in Service Precaution.

1. Install the retaining bolts to the multifunction turn signal lever.

• Tighten the retaining bolts to 7 Nm (62 inch lbs.) .

1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
2. Connect the steering column bulkhead connector to the vehicle wire harness.
3. Install the two wire harness straps to the steering column wire harness (1).
4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
5. Install the steering column knee bolster.
6. Install the steering column trim cover.
7. Verify that the lever is in the center or the OFF position.
8. Install the steering wheel to the steering column.
9. Enable the SIR system.
10. Connect the negative battery cable.

I hope this helps you.

Thanks

Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
3. Lightly lower the transmission to make room and pull out the dipstick tube.
4. Remove or disconnect the following:
   • Negative battery cable
   • Connector bracket from the front mount bracket
   • Harness connector
   • Starter bolts
   • Starter
   To install:
   
5. Install or connect the following:
   • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
   • Harness connector
   • Connector bracket to the front mount bracket
   • Dipstick tube
   • Transmission into position
   • 4 rear mounting bracket bolts
   • Negative battery cable
6. Remove the transmission jack

WITH MANUAL TRANSMISSION

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • Negative battery cable
   • Connector bracket from the front mount bracket
   • Harness connector
   • Starter bolts
   • Starter
   To install:
   
3. Install or connect the following:
   • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
   • Harness connector
   • Connector bracket to the front mount bracket
   • Negative battery cable

1.6L and 2.0L Engines

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • Negative battery cable
   • Wiring at the starter
   • Bolts attaching the starter to the engine
   • Starter
   To install:
   
3. Install or connect the following:
   • Starter and torque the bolts to 70 inch lbs. (8 Nm)
   • Starter electrical connections
   • Negaative battery cable

Maxima

1. Remove or disconnect the following:
   • Negative battery cable
   • Air duct
   • Harness protector from the harness
   • Starter wiring at the starter
   • Starter-to-engine bolts
   • Starter from the vehicle

     Image 89612G12l Not Found
     

   To install:
   
2. Install or connect the following:
   • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
   • Starter wiring
   • Harness protector
   • Air duct
   • Negative battery cable

Altima

1. Remove or disconnect the following:
   • Negative battery cable
   • Air inlet tube
   • Harness bracket
   • Wiring at the starter
   • Starter
   To install:
   
2. Install or connect the following:
   • Starter and torque the bolts to 60 inch lbs. (7 Nm)
   • Starter electrical connectors
   • Harness bracket
   • Air inlet tube
   • Negative battery cable

Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation

1. Remove or disconnect the following:
   Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle



Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle



Fig. Starter location and mounting detail-3.5L Maxima

To install:

1. Install or connect the following:
   Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable
   

1.6L, 1.8L & 2.0L Engines

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

1.8L & 2.0L Engines

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Remove or disconnect the following:
   Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
   

To install:

1. Install or connect the following:
   Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable
   

2.4L & 2.5L Engines

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable
   

2.4L Engine

1. Remove or disconnect the following:
   Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
   

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine

1. Remove or disconnect the following:
   Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter

To install:

1. Install or connect the following:
   Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines

1. Remove or disconnect the following:
   Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle
   
   
   Fig. Starter location and mounting detail-3.5L engine
   

continue...

Personally owning this car and installing several Hyundai stereo's, I would purchase a wiring harness kit from car audio shop or electronics retailer. The wire harness has a plug that connects to the cars wiring harness. This wiring harness kit will also list the wires to connect your new aftermarket radio to the harness. I would also recommend using crimped **** connectors to attach the two harnesses together.

This should Help:)

Battery WHITE/YELLOW (+) RADIO HARNESS
Accesory WHITE/RED (+) RADIO HARNESS
Ground BLACK (-) RADIO HARNESS
Illumination RED/BLACK (+) RADIO HARNESS
Dimmer RED (-) RADIO HARNESS
Power Antenna YELLOW/WHITE (+) RADIO HARNESS
Amp Turn On YELLOW/WHITE (+) RADIO HARNESS
LF Speaker (+) WHITE
LF Speaker (-) ORANGE
RF Speaker (+) YELLOW
RF Speaker (-) BROWN
LR Speaker (+) RED
LR Speaker (-) GREEN
RR Speaker (+) BLUE
RR Speaker (-) BLACK

Have your transmission fluid and filter changed. That should correct the problem.