Question about 2008 Suzuki GSXR1000
I have a gsxr 1000 2002 model that won't rev past 5000rpm I had the c28 and the c46 code I replaced the throttle bodies and the exhaust valve servo I have no more codes or f1 light but still won't rev @
Hi, Gord for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
04 1k Can rev over 5k RPM
Bike doesnt rev past 4 5k rpm
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Mar 25, 2018
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
I have seen this before a few things to do too make sure. First take the air filter out and shine a light use your fingers to move the slides up and down I suspect the springs that go on the slide is not seated in center you can tell from the slide going halfway and hanging up. Next, the boots on the slides only go on 1 way there is a notch on the carbs for them. I would guess this would fix you up if not we can get deeper into it with air-fuel mix screw settings.good luck
Posted on Mar 25, 2009
I have the same problem. I have heard that its an error that happens to a lot of Suzukis. It has something to do with the feul injection and it shouldnt effect the performance. Its just a matter of going to a bike shop where they can hook their computer and clear the fault.
Posted on Aug 11, 2009
SOURCE: f1 code on my 2006 suzuki gsxr
When the red light comes on, eg (F1) use these fault codes to find your problem. To extract the codes from the computer system, there is a two pinned connector hanging out of the wiring harness, on the left hand rear of the bike, (say above the pillion foot peg under rear trim. Be sure not to confuse the other connector used by the Suzuki Workshop Mechanics, as this has four or five wires to the connector) After locating the one with only two wires at the back, use a split pin or paper clip to bridge the two wires togeather and turn the ignition to the ON position. You should now be able to read the code on the console. The fault codes are as follows,,
**** GSXR Fuel Injection (FI) Code List:*****
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR C29 - SECONDARY THROTTLE POSITION SENSOR C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
Posted on Feb 03, 2010
Tips for a great answer:
Feb 09, 2018 | 2009 Suzuki GSXR1000
Jan 25, 2017 | 2008 Suzuki GSXR1000
Apr 02, 2016 | Suzuki Motorcycles
Sep 26, 2012 | 2004 Suzuki GSX-R 1000
Jan 04, 2011 | 2003 Suzuki SV 1000 S
Dec 07, 2009 | 2004 Suzuki GSX-R 1000 Mladin Replica
Apr 24, 2009 | 2002 Suzuki GSX-R 1000
346 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: