Question about 2003 kawasaki VN 1500 Vulcan Classic

1 Answer

2003 Kawasaki vn1500 wont start!Tried fully charging battery which holds at v12.4ish Had clicking noise from start relay so changed for new one. Now no click but clicks from ISC valve ?

Thought it was Meta TV2 alarm as appeared dead so bought and fitted replacement - alarm now appears to work OK but engine still wont fire. Checked all fuses, cables, starter lockout switch, starter starter switch etc. Getting click from ISC valve for front cylander is only clue. Please help. Thanks, Jim.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • kawasaki Master
  • 58,765 Answers

Hi, Jim and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www2.vulcanrider.se/DL/00-08ka-smcvulcan1500classicfi-s.pdf
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki/kawasaki-vulcan-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on Oct 03, 2016

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kawasaki Vulcan Classic will not start


Hi, JD #4 and #7 are jumping up and down holding brightly colored neon signs that say "PICK ME" and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Bike Won START clicks won turn over
Why is my Kawasaki VN800 Classic not starting
Kawasaki VN1500 Service Manual
OEM Parts for Kawasaki
Download Manual 1998 Kawasaki Vulcan 1500 Classic Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 22, 2016 | 1998 kawasaki VN 1500 Vulcan Classic

1 Answer

1998 kawasaki VN1500 Vulcan Classic Motorcycles


try cleaning the start button inside the housing as weather gets in and could be a dirty contact ! check the earth contacts around the engine also ! are the wires to the solinoid in good condition , battery wires also ?

Apr 24, 2014 | kawasaki VN 800 Vulcan Classic Motorcycles

1 Answer

Kawasaki vn1500 will not start,new battery,new starter solenoid,good fuses,just click click click not start


Check your ground connection to make sure that it is clean and tight. If the connections are good, I would suspect the starter itself.

Apr 24, 2014 | kawasaki VN 800 Vulcan Classic Motorcycles

1 Answer

1997 Kawasaki VN 1500 Vulcan Classic will not turn over


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Electrical Problem 95 VN1500 Kawasaki Forums
bike won turn over anymore Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
http://xn--80azbq.xn--p1ai/failo/Kawasaki_VN1500__87-_99_Service_Manual.pdf
OEM Parts for Kawasaki
1997 Kawasaki Vulcan 1500 Classic Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 21, 2014 | 1997 kawasaki VN 1500 Vulcan Classic

2 Answers

2003 Ford Taurus will not start. Have tried jumping the battery but still nothing. When turned on, all dash lights come on and then there is a click sound when we try and turn it over.


2003 taurus not starting the lights on dashboard not coming on.windows wont go up and wont crank ..anyone know what to do ..please

May 14, 2012 | 2003 Ford Taurus

1 Answer

2001 Kawasaki VN 1500 Vulcan Classic will not start just clicks


Hi, Hornet you turn on the ignition switch press the starter button and all you get is the dreaded "CLICK" now before testing any electrical component in the Starter System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries and the usual suspects are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid cannot drop more than 1/2 volt of battery voltage.
4. Disconnect spark plug cables, with a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 9.6 volts DC. If the voltage is below 9.6 the battery is faulty and must be replaced. I "HIGHLY" recommend a maintenance free AGM battery typically they have more amperage for cranking.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buying a new one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike Won START clicks won turn over
http://tearitupfixitrepeat.blogspot.com/2010/08/if-your-1500-vulcan-wont-start.html
Kawasaki Vulcan 1500 Classic Fi Service Manual
OEM Parts for Kawasaki
2001 Kawasaki Vulcan 1500 Classic Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jun 29, 2011 | 2001 kawasaki VN 1500 Vulcan Classic

1 Answer

2002 Kawasaki VN 1500 Vulcan Classic fuel pump not priming


Hi, G_man2705 before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.kawasakimotorcycle.org/forum/mechanics-corner/140182-04-vulcan-nomad-1500-fuel-pump-wont-cycle-prime-up.html
fuel pump not pumping electrical issue Kawasaki Vulcan Forum Vulcan Forums
Kawasaki VN1500 MEAN STREAK Service Manual
OEM Parts for Kawasaki
2002 Kawasaki Vulcan 1500 Classic Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 22, 2011 | 2002 kawasaki VN 1500 Vulcan Classic

1 Answer

My 2002 kawasaki ninja 250 is having trouble starting. (electric start) At first it was just giving me this clicking sound kinda like when your car wont turn over and start. So I replaced the battery for...


The oil light is on because the engine isn't running to build any oil pressure. Sounds like the new battery may need to be charged fully. After the battery is fully charged, and the 'clicking' noise is back (or not) check the battery connections for corrosion--especially at the positive terminal. If ok, you should get one solid click when trying to start. If ok, but still not starting, jump the two heavy terminals of the solenoid (click source) with a heavy wire which should bump the starter motor. If nothing, then the starter motor needs service--usually the brushes inside fail to make contact with the armature due to brush wear, or weak springs. Most dealers will likely only sell you a new starter--no internal parts. Hope this helps!

Oct 04, 2010 | kawasaki Ninja 250R Motorcycles

1 Answer

2002 Kawasaki VN 1500 Vulcan Classic no electrical power


Hi, Fabian10 before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
No power when switch is turned on
No power to anything Stumped Kawasaki Vulcan 750 Forum Kawasaki VN750...
Kawasaki VN1500 MEAN STREAK Service Manual
OEM Parts for Kawasaki
2002 Kawasaki Vulcan 1500 Classic Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Sep 28, 2010 | 2002 kawasaki VN 1500 Vulcan Classic

1 Answer

Bike wont start just a clicking


Hi and welcome to FixYa,

Initially, charge and load test the battery.

Offhand with a fully charged battery, jump the 2 big terminals of the starter relay. If the starter motor spins, then faulty starter relay.

Good luck and thank you for asking Fixya.

Apr 17, 2010 | 1990 kawasaki ZZR 1100

Not finding what you are looking for?
2003 kawasaki VN 1500 Vulcan Classic Logo

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5954 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

ROB

Level 3 Expert

858 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...