Motorcycles Logo

Related Topics:

evela elrod Posted on Apr 14, 2015

My 1980 pe 250 is getting fire from magnetio to cdi box but not to coil put new cdi box off a running pe 250 and still no fire to coil

1 Answer

jonpoint

Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Welcome Back:

Visited the website for 2 consecutive days.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 17 Answers
  • Posted on Oct 20, 2017
jonpoint
Contributor
Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Welcome Back:

Visited the website for 2 consecutive days.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Feb 04, 2008
Answers
17
Questions
0
Helped
13826
Points
41

Check the coil. Swap it with another if possible to check. Sometimes coils fail short-circuit on the primary. If so, you will see no signal from the CDI when attached to the coil.

5 Related Answers

Anonymous

  • 6966 Answers
  • Posted on Nov 15, 2009

SOURCE: i need a wiring diagram for a honda cr 250 so i

Hi and welcome to FixYa,

On your posted need for the wiring diagram of a Honda CR250, would this help?

Good luck and thank you for asking FixYa.

Ad

Anonymous

  • 311 Answers
  • Posted on Dec 30, 2009

SOURCE: no spark put on a new cdi box coil good and a new

hi,sounds to me like your cdi pickup unit has failed,i am not 100% certain but this will be located on the end of the crankshaft behind one of the enginecovers,there could be two other possibilities,motox bikes are notorious for breaking wires so check the wiring from the cdi sender unit to the cdi box and the coil,also check your "off"button it may be stuck in the "kill" position..hope this helps..cheers ian

Anonymous

  • 2702 Answers
  • Posted on Jul 12, 2010

SOURCE: 2007 KXF 250 electrical problem

when the ignition parts like the coil and the transistors in the cdi unit gets warmed up they dont work as well as when there cool,,,so a problem thats not there when cold will be there when its hot,,,,if the stator has a small fault in it when cold when it gets hot it turns into a big fault! the best way to find this fault is by swoping one part at a time till you fine the faulty part,,,or put it into the bike shop and pay through the knows for the fix? have you a friend with the same type of bike you could swop the parts with??? it a big big help if you have! i would start with the coil then the cdi unit,,,there the most likley parts to play up when they get to hot they go faulty!

astrawoid

Eric Cross

  • 294 Answers
  • Posted on Dec 07, 2010

SOURCE: weak spark--put on a new

May be CDI, but check all your grounds first. Make sure you have a clean metal to metal connection of the coil to frame. Disconnect the leads going to the kill switch also. you may have a high resistance to ground short. Also, did you replace the lead coming out of the coil going into the spark plug? did you reuse the old lead?

grizzlyrecon

  • 70 Answers
  • Posted on Jul 09, 2011

SOURCE: i have no spark on

if you have replaced all that it sounds like it is the stator. its an alternator for small engines. get one on ebay cause factory are always expensive. its located behind the pull start. take that off then the side case cover.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

No spark on my 250 cc ATV

Check CDI, but also specify which coil you changed, stator coil or HT coil.
Jan 19, 2015 • Motorcycles
0helpful
1answer

No spark but motor turns over on 1987 honda fourtrax 250

possibly the rectifier faulty or stator coil
Sep 04, 2014 • Motorcycles
0helpful
2answers

1977 yz 250 isn't getting fire

Check the points for proper gap and clean. The old school bikes used more than just coil and plugs. Also, often overlooked, check the kill switch connection. Often this is the case on Yamahas.
0helpful
1answer

Can't Start 1981 Yamaha SR250

find a running sr 250 and swop his cdi unit with yours if the bike runs, fine. if not put his cdi back in and try again. if the good bike now starts it will indicate that your cdi is faulty. the cdi is located under the tank inside the frame. don't buy a second hand cdi unless you can test it on a working bike. they are very expensive and you don't want to buy a dud
1helpful
1answer

I have a kz250 engine but no cdi box can i use another one to replace this one or do you know where i can get one from

Hello Pam, the controllers on the Kawasaki, KLT 250 Prairie, 1983-1985 are suppose to be the same...i have never swapped a CDI controller on the older KZ 250's, so i can not advise if another unit would work. I did however locate a new replacement for your bike. Here is the link.
I hope this helps & good luck with your bike.
http://cgi.ebay.com/ebaymotors/CDI-box-Kawasaki-KZ250-1980-1983-KZ-250-/250839194546?pt=Motors_ATV_Parts_Accessories&hash=item3a672e5bb2
0helpful
1answer

1980 xs400 se will not get spark some wires burnt

possible the cdi unit went the journeyat the same time, only way to tell is to try another cdi. best of luck.
2helpful
1answer

Does not run

if you do not have fire only three things control this stator coil cdi more than likley you have a bad cdi u can get the cdi off ebay cheapest
0helpful
2answers

Lost all elce, power while riding my 1980 kawaski 750 ltd 4cyl. just shut down, no elec. power at all now. ck'ed battrey and terminals

It is either the stator plate or coil if not getting spark, if it is just the electronics part, then it is the cdi box or equivelant
Not finding what you are looking for?

225 views

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Brad Brown

Level 3 Expert

19187 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66915 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...