Question about 2003 Suzuki VL 1500 Intruder LC
Where is the oil fill port on the Suzuki intruder lc 1500 2003 model? @
Hi, John for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2003 Suzuki VL 1500 Intruder LC oil change Google Search
Suzuki C90 Oil Change and Final Gear Oil Boulevard
Suzuki VL1500 Service Manual
Posted on Sep 22, 2018
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
One the left-hand side of the bike (facing forward), there is cover plate just ahead of the drive shaft. Remove that cover (mine has 8mm bolts). The bleeder valve is under this cover. Go to an auto parts store and get a "one man bleeder kit" or if you have some plastic tubing that will fit over the valve, you can use that and a clean jar. Follow the instructions on the bleeder kit, or if you're using the jar and tubing, fill the jar about a quarter of the way with break fluid (use DOT4, but never DOT5!). Take the cover off the master cylinder up at the handlebars, place the tube over the end of the bleed valve (after loosening it a turn or two. Place the other end of the tube down in the break fluid in the jar. Work the clutch lever until you stop getting bubbles in the jar. Be sure to keep the fluid level up in the reservoir. Tighten the bleeder valve, remove the tubing, top off the fluid and replace the covers.
Be careful not to get brake fluid on anything. It will eat paint and mess up other things.
Posted on Feb 13, 2009
Likely the clutch master cylinder on the handlebar needs rebuilding--a check valve or piston cup is bypassing fluid when pressure tries to build up. If it was the slave cylinder, it would probably be leaking fluid. Same with the coupling hose.
Posted on Sep 14, 2009
Testimonial: "Thanks for the next step"
If they cant duplicate it your good.Usualy with backfiring i would make sure to eliminate any exhaust leaks. The dealer is inexperienced at solving compound problems,(sorry) not picking a fight, but sometimes cleaning is not goog enough,I went through this with a 1400 Intruder.several attempts were needed to get the two carbs level on the same line with each other.so the floats would work properly together,then set fuel flow and the air flow through the ventouri in the carbs.Also i had to make these adjustments while level (not on side stand) The floats were very sencitve to needle valve to seat adjustment(bent to open or close some of the flow)
Posted on Apr 12, 2010
Hello Dale, this is an easy job on your bike. Use a flat head screw driver and remove the brake pad cover...it will pop off.
Remove the hairpin type clips off of the ends of the brake pad pins.... Use pliers & pull the brake pad pins out from the front of the rear brake caliper....Clean the rear brake caliper's piston with brake cleaner. Use a rag and wipe it clean...Reinsert the old brake pads into the caliper. Place a pry bar between the brake pads, then push the inner piston into the caliper body, this will allow room to install new pads.... Remove the old brake pads...Coat the brake pad pins and the new brake pads metal back plates with high-temperature grease.
Slip the new brake pads into the rear brake caliper, then push the brake pad pins halfway into the caliper. Slip the spring clips into place between the brake pads and the brake pad pins. Push the brake pad pins completely through the rear brake caliper. Push the hairpin clips back into the brake pad pin tips. Snap the brake pad cover onto the top of the rear brake caliper....
Pump the rear brake pedal until the pedal feels firm, indicating that the brake pads have closed around the brake rotor...No bleeding will be needed because the system was never opened - That's all there is to it...i hope this information is helpful & good luck with your bike.
Posted on Nov 23, 2011
Tips for a great answer:
Mar 15, 2018 | 2000 Suzuki VL 1500 Intruder LC
Jul 05, 2016 | 2004 Suzuki Intruder LC 1500
Mar 16, 2011 | 2003 Suzuki VL 125 Intruder LC
Jun 16, 2010 | 2001 Suzuki VL 1500 Intruder LC
Jun 07, 2010 | 2001 Suzuki VL 1500 Intruder LC
Apr 11, 2010 | 2002 Suzuki VL 1500 Intruder LC
May 05, 2009 | 2003 Suzuki VL 125 Intruder LC
425 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: