Remove light covers

The support page with free manuals is here.
http://shared.whirlpoolcorp.com/product_literature/search_results.jsp?searchTerm=MMV5208WW1&siteCd=WHRCOM&userType=Consumer

The owner's manual says:

Cavity light: The cavity light bulb is located behind the vent
grille at the top front of the microwave oven, under the bulb
cover, and is replaceable. Remove two screws on the vent
grille, tilt the grille forward, and lift it out. Open bulb cover and
replace bulb. Close bulb cover, replace vent grille, and secure
with screws.

Cooktop light: The cooktop light bulb is located on the
underside of the microwave oven, and is replaceable. Remove
bulb cover screw, and open the bulb cover. Replace bulb,
close bulb cover, and secure with screw.

To remove the grille, see my video at microwavecontrol.com.

Good Afternoon Friend,

I understand that you want to know how to remove the cover on your Frigidaire microwave, model# FGMV205K. There are two different covers that you are able to remove for access to two different light bulbs.

If you are trying to change the Microwave Oven Light for inside your microwave:

1)To replace light bulb, first disconnect power to your microwave oven at the circuit breaker panel or by unplugging it.

2)Remove the louver by removing the three Hood Louver Screws.

3)Push in the upper tabs and pull the louver away from your appliance.

4)Remove the light bulb and replace with a new 20 watt light bulb. DO NOT USE BULB LARGER THAN 20 WATTS.

5)Close the Oven Light Cover by carefully pushing into place. Push the louver back into place (engaging both the bottom and top tabs) and change to hood Louver Screws.


If you are trying to change the light bulbs underneath your Microwave:


1)To replace light bulbs, first disconnect power to your microwave oven at the circuit breaker panel or by unplugging it.

2)To open Light Cover, remove the screw on the light cover.

3)Replace the light bulbs with new 20 watt light bulbs. DO NOT USE BULBS LARGER THAN 20 WATTS.

4)Close the Light Cover and secure with screw removed at step 2.

If further troubleshooting is needed, I ask that you please let me know the error codes displayed on your appliance. Hope this is helpful.

-Best Regards-
WP

I have an Amana AS12575GRB01, the cover to the light bulb on the fridge side is mounted on the top inside back right corner. Having problems removing it

Try unthreading the cover. Rotate to the left, or counterclockwise.

To remove the front bumper cover you must first remove the turn lights in
the bumper. To do this remove the fog lights or the fog light covers by
removing the screw under the cover and remove the screw from the bottom that
holds the light in place. After doing this you will see a 12mm bolt behind
the light and one just to the inside of the lower grille. Remove all 4 of
these bolts(2 per side). Also remove the bolts /clips in the lower panel
under the bumper. The corners of the bumper near the fender actually slide
onto a stud that holds it in place. Just remove the bumper by pulling
forward. Sorry if this seems confusing but it is really pretty easy to do.

go to this link, once your on the acura site scrol down till you see the diagram
http://www.acura-legend.com/vbulletin/f4/bumper-cover-removal-128134/

Hello,

Unplug the Whirlpool refrigerator from the electrical outlet.
Step 2
Locate the bulb on the inside of the Whirlpool refrigerator.
Step 3
Remove the light cover. Usually these just snap off, but, on some models, they may need to be unscrewed. Use your screwdriver to unscrew the light cover retaining screws (if required).
Step 4
Unscrew the old light bulb.
Step 5
Screw in the new light bulb.
Step 6
Replace the light cover. Plug the Whirlpool refrigerator back in. Test your new light bulb.
Also note that the below can also work

Unplug refrigerator or disconnect power.
Slide the light bulb cover toward the back of the compartment to release it from the light assembly.
Replace burned-out bulb(s) with appliance light bulb(s) no greater than 40 watts.
Replace the light bulb cover by inserting the tabs on the cover into the liner holes on each side of light assembly. Slide the cover toward the front until it locks into place.

NOTE: Do not force the cover beyond its locking point; doing so may damage the light cover.
Plug in refrigerator or reconnect power.
To change the freezer light bulb:

Unplug refrigerator or disconnect power.

NOTE: You may need to remove the upper freezer shelf or basket to access the light assembly.
The light bulb cover opens from the back. Firmly press forward on the notches in the back of the cover and pull down the cover.


Remove the cover and replace the burned-out bulb with an appliance bulb no greater than 40 watts.
Insert the front tabs of the cover into the liner and snap the back portion of the cover over the light assembly.
Plug in refrigerator or reconnect power.

Good luck in applying the solution

That's covered on pages 35 & 36 of the owner's manual here.

Cooktop Light/Night Light

On models JVM1850, JNM1851, DVM1850 and
EMO4000, replace the burned-out bulb with a 120 volt,
40-watt incandescent bulb (WB36X10003), available
from your GE supplier.

On models JVM1870, JVM1871, JVM2050 and
JVM3670, replace the burned-out bulb with a 120 volt,
20-watt halogen bulb (WB36X10213), available from
your GE supplier.

To replace the bulb(s), first disconnect the
power at the main fuse or circuit breaker panel
or pull the plug. *

Remove the screw at the left edge of the light
cover and push on the right edge of the cover
to open.

Be sure the bulb(s) to be replaced are cool
before removing. After breaking the adhesive
seal, remove the bulb by either gently turning
(for models JVM1850, JNM1851, DVM1850 and
EMO4000) or pulling straight out (for models
JVM1870, JVM1871, JVM2050 and JVM3670).

Replace with the same size and type bulb.

Raise the light shield and replace the screw.
Connect electrical power to the oven.

Oven Light

Replace the burned-out bulb with a 120 volt, 20-watt
halogen bulb (WB36X10213), available from your
GE supplier.

To replace the oven light, first disconnect the
power at the main fuse or circuit breaker panel
or pull the plug.

Remove the top grille by taking out the screws
on top of the grille that hold it in place and
sliding the grille to the left (opening the door
makes grille removal easier).

Next, remove the light cover.

On some models, the light cover is located
in the center of the top opening. Remove the
screw that secures the light cover and lift the
cover off.

On some models, the light cover is located at the
left of the top opening. Lift the cover off.

Pinch the clips that hold the light socket in
place and lift the socket out.

Remove the bulb from the light socket by
pulling straight out. Replace with the same size
and type bulb, then replace the light socket and
cover.

Replace the grille and screws. Connect electrical
power to the oven.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

* If your control board was damaged (lights won't come on, won't go off, fan or turntable not working right) after a cooktop light bulb blew or was inserted or removed while power was on, see here.

Some models are different...I hope this helps.

Replacing Light Bulbs
To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before replacing light bulb. After replacing light bulb, reconnect power.
To avoid personal injury or property damage, observe the following:
• Allow light bulb to cool.
• Wear gloves when replacing light bulb.
Fresh Food Section
(style of light shield varies)
1. Slide clear light shield toward back of compartment to release from light assembly.
2. Remove light bulbs.
3. Replace with appliance bulbs no greater than 40 watts.
4. Replace light bulb cover by inserting tabs on light shield into liner holes on each side of light assembly. Slide shield toward front of refrigerator until it locks into place. Do not force shield beyond locking point. Doing so may damage light shield.
Freezer (style of light shield varies)
1. Reach behind the light cover.
2. With firm pressure, press forward on the notches at the back of the cover and pull down the cover will open from the back.
3. Remove the cover.
4. Remove light bulb
5. Replace bulb with appliance bulb no greater than 40 watts.
6. Insert front tabs of light cover into slots in freezer liner and snap rear portion over light assembly until rear tab engages.

Ric

You remove three or so nuts and remove the light assy/housing. The steel cover as you put it is your body