I have a scooter, XZ260T-4 whcih does not get any fire to the ignition at the spark plug. All seems to be right otherwise. Any suggestions?

That's the diagram

Sounds like ignition coil / lead issue. I don't know the specifics of your bike but I am guessing by the fault that there is an ignition coil pack on top of each spark plug. Try swapping the coils from the working ones to the non-firing ones and see if the problem is consistent. Otherwise you are probably looking at wiring issues.

You need to check for a spark. There are a few ways to do this. The easiest way is to remove the spark plug and put it back in the spark plug cap. Then ground it to the engine - you should be able to lay it against a non-painted portion of the engine. Make sure there is good metal-to-metal contact. In a semi darkened area, attempt to start the scooter. You should see a definite spark at the tip of the spark plug. It's hard to see in direct light. If the color of the spark is blue, that means it's a strong spark. A white color is less strong, and a yellow color is weak. Most scooter starting systems are a bit weak (compared to cars). Even a yellow spark should start your scooter just fine.
The spark must occur at the right time. Just about all scooters made since around 1980 have an electronic ignition. These systems can rarely be set. In general, the spark occurs just before the piston reaches the top of it's stroke. There is a slight delay between the spark plug fire and the fuel-air mixture ignition. That's why the spark occurs a little early. Most ignition systems have an advance unit build in. As the engine speeds up, the time of the spark retards a little bit. This helps the engine fire the mixture at the proper time.
Install a new spark plug (especially if the engine is a two stoke). Clean or replace the air filter as necessary. The carb, air cleaner, and exhaust pipe are all carefully tuned to work together. Most scooters absolutely WILL NOT run correctly if any of these parts are changed in a haphazard manner!
Double check all connections, then crank your scooter for 10-15 seconds. Did it start? Do you hear any popping? It should sound like the engine is trying to run. Most scooters will not start if you apply throttle while cranking. If the scooter catches, but doesn't start, let it rest 15 seconds before trying to start it again.

hope this helps

John

It is stamped on the top of the engine, in the head. It is usually pretty easy to find, and you wont have to remove any pieces to see it.

2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
   NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
2. Remove the intake manifold cover, if required.
3. Disconnect the left side spark plug wires from the spark plugs.
4. Disconnect the left side spark plug wires from the ignition coil.
5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
6. Remove the spark plug wire assembly.
7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
8. Disconnect the right side spark plug wires from the spark plugs.
9. Disconnect the right side spark plugs from the ignition coils.
10. Remove the spark plug wire assembly.
11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.

To install:

1. Install the spark plug wire assembly.
2. Connect the right side spark plugs to the ignition coils.
3. Connect the right side spark plug wires to the spark plugs.
4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
5. Install the spark plug wire assembly.
6. Connect the left side spark plug wires to the spark plugs.
7. Connect the left side spark plug wires to the ignition coil.
8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system


Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system


I really hope help you with this (remember rated this help) Good luck.

The ignition timing may have been disturbed,or if it is equipped with a carburettor,the mixture setting may have been disturbed,or the carb.jet may be blocked by dirt in the fuel or the spark plug may be faulty .get all these checked first .