- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
My suggestion would be to remove the hose between the air intake and the throttle body, look in side it and see if there looks like carbon buildup inside. If so you may have to remove it and clean it with brake cleaner and a stiff brush. Don't learn the hard way like me, wear EYE PROTECTION!!! can't stress this enough.
remove air cleaner with clip,
remove filter
remove allen head bolts on plastic cover.
# all connectors i took off the top first.
then change the bottom 1 at a time..
install the ivm back in place with plastic clip in (push back in place)
Please see my tip at http://www.fixya.com/cars/r5929960-s_thermostat .These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.
Remove the air cleaner intake duct.
Partially drain the cooling system.
Remove the radiator inlet hose from the thermostat housing.
Remove the thermostat housing bolts.
Remove the thermostat.
Clean and inspect the thermostat housing gasket mating surfaces.
To install:
Install the thermostat.
Install the thermostat housing.
Install the thermostat housing bolts and tighten to 18 ft. lbs. (25 Nm).
Install the radiator inlet hose to the thermostat housing.
The fan/clutch assy has left hand thread. Loosen by turning clockwise.
Remove radiator top shroud & air cleaner assy. to gain access.
Remove engine cooling fan by holding the belt drive pulley with a suitable flat bar tool (that fits over the top of the drive pulley attachment bolts), then using a suitable flat spanner to unscrew the fan clutch assy (clockwise). When re-fitting, tighten clutch nut to 30 ftlb.
You may need to use a bit of ingenuity in making the flat bar holding tool, unless you are able to procure the BMW tool #11.5.030.
Good luck
please rate as problem solved if this is what you need.
Section 03-14: Engine Controls, Electronic
1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION
Intake Air Temperature (IAT) Sensor
Removal and Installation
Disconnect battery ground cable (14301) .
Disconnect engine control sensor wiring (12A581) from intake air temperature sensor (IAT sensor) (12A697) .
Remove intake air temperature sensor from air cleaner outlet tube (9B659). (This is the tube that goes from the air cleaner to the engine.)
To install, reverse Removal procedure. Tighten intake air temperature sensor securely.
My sincere apologies for the delayed response. I am personally going back to answer your unanswered questions. I have only been a free contributor to this site for the past 4-months.
I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.
CLICKon the following LINKS. It has the Belt Diagrams you will need.
I do not know if you have the 528 or 540 Model; however I have included both Links below.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
1.Remove the air duct connected to the air cleaner. 2.Disconnect the intake air temperature sensor harness. 3.Remove the air intake hose from the air cleaner side. 4.Remove the air cleaner cover and filter. 5.Remove the air cleaner mounting bolts and remove the air cleaner.
INSPECTION
1.Check the air cleaner body, cover, or packing for distortion, corrosion or damage. 2.Check the air duct for damage. 3.Check the resonator for distortion or damage.4.Check the air cleaner element for restriction, contamination or damage.If the element is slightly restricted, remove dust and other contaminants by blowing air from the upper side through the element.5.Check the air cleaner housing for restrictions, contamination or damage.
INSTALLATION
Installation of the air cleaner is the reverse order of removal
×