Question about Yamaha Road Star Midnight Silverado Motorcycles
When I try to start my bike the decompression solenoid just clicks. I have a new battery, starter and starter relay on the bike. The manual says there is no test procedure to check the decompression solenoid. Anu ideas as to what I can check?
The clicking may be the starter solenoid. Check for a dead battery or defective solenoid.
Posted on Apr 13, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
I had the same problem 2001 XVS1100 Custom
this is a starter issue Over time the starter on this bike twists when its under a load.
Look at the two bolts holding the starter on if they are not straight across then its twisted. turn starter back in line with a pair of big channel locks and try to start this should do the trick if this works i would recommend taking the two bolts out and bend them back straight or replace and reinstall starter this should fixya problem
Hope this helps ...............Jimmyfixya
Posted on Jul 08, 2009
You didn't mention what year model your bike is so I'll just generalize my response. Since you said that you replaced the solenoid, I'll assume that your bike is a 1988 model or earlier.
Your bike has a starter relay if it still has the stock wiring on it. Harley has used a starter relay since 1965 on the first model of ElectraGlide. Usually, it's underneath the battery tray or the seat or around that area.
On the back of your solenoid, you have three wire connections. Two very large connectors and one small connector. Make sure your bike is out of gear (in neutral) and use an old screwdriver to short between the large connector that comes from the battery and the small wire connection. The starter should engage and try to start the engine. If the ignition switch is on, it will start the engine. The starter will turn using this method with or without the switch being in the "on" position. If the starter works using this method, the problem is in either the relay or the neutral switch. If the starter does not turn the engine over, the problem is in the solenoid.
Now, let's check a few things. The small connector on the back of the solenoid should have a green or pink (depending on year) wire on it. Using a voltmeter or a test light, make sure you have voltage at the connector when you press the starter button with the switch in the "ON' position. If not, follow the wire to it's source, the relay.
The starter relay can be one of several different designs used throughout the years. It could be a small plastic cube, a small metal can, or a round phonelic relay. The relay should have four connections on it. A "hot" wire, a wire from the handlebar switch, the wire going to the starter, and a ground. The ground may be through the case itself. On the older Shovelhead bikes (1984 and earlier) there was a small short black wire that ran from the starter relay to the transmission for the ground. This wire must be intact or the relay would not work due to lack of a ground.
When you turn the switch on, one of the wires to the starter relay should become "hot". When you press the start button, you should hear a slight click and another of the smaller wires should now be "hot" as well, the one going to the starter.
On some year (1972 and later) models, the neutral switch was wired in with the starter relay. This was to prevent the bike from starting while "in gear" by disabling the relay. You'll have to figure this one out for yourself since I don't know what year model your bike is.
Now, you said you had power to the solenoid when you pushed the starter switch. So, let's assume that the starter failed the first test to told you aboue. If so, the problem is still most likely in the solenoid. Inside the solenoid, there is a large plunger with a copper disc on it. When you depress the starter switch, the coil in the solenoid becomes magnetized and pulls the plunger towards the back of the solenoid. This does two things, it engages the starter drive with the ring gear on the outer clutch drum and makes a high current electrical connection. The copper disc makes contact between the two large connections on the back of the solenoid from the inside. This connects the battery to the starter motor through the solenoid. If the black phonelic plate on the back of the solenoid is cracked or the contacts inside of it are badly burned, it will not work.
Now, if the solenoid is working correctly and you are getting voltage to your starter, it could be the brushes or something inside the starter. This is indicated if the starter trys to turn the engine over but just can't. It won't have enough power if the starter field windings are bad.
I hope I've given you something here that will help you solve your problem. This is basically the electrical part of the starter system. There are mechanical parts as well. If you hear the starter turning but the engine doesn't turn over, you have a mechanical problem. You can either repost or you can contact me directly at firstname.lastname@example.org I'll help if I can. Good Luck!
Posted on Nov 05, 2009
Same problem here ... 2008 C90T ... dealer no help ... in 3rd or 4th, ignition off, force it to roll backwards until you hear the piston shift ... should start then. Told it's the rear piston stopping at or near top dead center, but also told adjust the decompression will "solve" the issue; anyway, a rolling forward-start in 4th will work, too, otherwise try rolling the bike backwards until you hear, and you will know when the piston moves and then it will start.
Posted on May 25, 2010
SOURCE: Try to start my 1600
is the battery flat?.start with that!!..if not..are the battery termanials done up tight on the battery...then check that solenoind termenals are done up...hope this helps
Posted on Sep 04, 2010
Put your charger on charge for a day or so ... is it a maintenance free battery? If so, charging is your only option. If you can get into the cells, you could perform a hydro test on it ... you will be looking for a number near 1300. If you don't have a hydrometer, you may want to take the battery to a auto parts store for them to test it.
Thanks for your interest in FixYa.com
Posted on Nov 23, 2010
Tips for a great answer:
Jun 25, 2018 | 2000 Yamaha XV 1600 Wild Star
Mar 23, 2015 | 2003 Yamaha Road Star Silverado
Nov 25, 2012 | 2000 Yamaha DT 125 R
Sep 02, 2012 | 2002 Yamaha XV 1600 Wild Star
Sep 04, 2010 | Yamaha Road Star Midnight Silverado...
Aug 02, 2009 | 2002 Yamaha TT-R 250
Jul 09, 2009 | 2000 Yamaha XV 1600 Wild Star
Dec 23, 2008 | 2000 Yamaha YZF-R1
1,092 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: