Question about Keeway Motorcycles

Open Question

Keeway fuel pressure regulator vacuum - Keeway Motorcycles

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: Checked Fuel Pressure Regulator on 93 Ford Tempo GL 2.3 Liter.

As far as I know without checking it personally it sounds like it could be one of three things (in order from easiest to hardest). Clogged air filter, worn timing chain, leaking head gasket. To check for the third go to Auto Zone and get them to do a compression check, its free. I can't remember off hand but if the 93 has a TPS (throttle position sensor) that could also cause an irratic idle.

Posted on Mar 18, 2009

Ad
  • 92 Answers

SOURCE: fuel pressure regulator had no vacuum line connected

another engineers wet dream. think of it this way . what is normally in the intake when the engine is running.. answer vacume, hence the regulator gets its vacume without a hose connected to it as its already in a full time vacume chamber.no hose required . ps be carefull to seat the regulator and o rings securely into the housing befor you reattach the secureing metal clip.
good luck chris

Posted on Mar 23, 2009

  • 335 Answers

SOURCE: fuel leaking into vacuum line on fuel pressure regulator

If you have fuel on the vacuum side of the reg, that means the reg is leaking,causing a variaty of drivabiliy problems. Replacing this reg is very straight forward. Just add a little lube to the O-ring on the reg before installation. Good luck.
Yours Moe.

Posted on Apr 23, 2009

polarcycle
  • 1392 Answers

SOURCE: vacuum line for fuel pressure regulator 98 Tahoe

Was there a hose on the old one? If not, you don't have one. It is most likely your fuel pump if you are not getting fuel.

Posted on May 31, 2009

  • 1 Answer

SOURCE: toomuch fuel pressure. fuel regulator replaced

how do you know it has too much fuel pressure? what is your car doing?

Posted on Jun 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a keeway superlight 125 and it started fine the other day but as so as I put it in gear it shut off When I got it started I went 8miles then it started dying and then cut off and wouldnt start


Hi, Craig this is a generic troubleshooting guide the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Water or dirt in the fuel system, carburetor or filter.
11. Restricted, blocked or kinked fuel line.
12. Fuel tank empty.
13. The gas cap is not venting properly or fuel tank venting system blocked.
14. A failed fuel pump, pressure regulator and or fuel injectors.
15. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
16. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day.
What to do When Your Motorcycle Won Start
troubleshoot motorcycle not starting
TROUBLE SHOOTING
KEEWAY Speed 125 User Manual
KEEWAY SUPERLIGHT 125 150 SCOOTER SERVICE REPAIR PDF MANUAL DOWNLOAD 2006...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


May 09, 2016 | Keeway Motorcycles

1 Answer

I have a 2007 keeway hurricane and wont start


Hi, Brandon the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or damaged battery, 9 volts or lower.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Water or dirt in the fuel system, carburetor or filter.
11. Restricted, blocked or kinked fuel line.
12. Fuel tank empty.
13. Gas cap is not venting properly or fuel tank venting system blocked.
14. A failed fuel pump, pressure regulator and or fuel injectors.
15. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
16. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable free downloads that you need please visit the websites below. Good luck and have a nice day.
50cc keeway hurricane problems
Help Scooter won start cleaned carb which hoses
Scooter Troubleshooting Scooter won start All about Scooters
http://www.49ccscoot.com/manuals/Keeway_50cc_2T_Service_Manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Feb 21, 2016 | Keeway Motorcycles

2 Answers

98 buick regal has a strong gas smell


Do you know what fuel pressure regulator is ? These like to leak when they get older !
The cartridge type fuel pressure regulator (1) is a diaphragm-operated relief valve (6) with fuel pump pressure on one side, and regulator spring (2) pressure, and intake manifold vacuum on the other side. The regulators function is to maintain a constant fuel pressure across the injectors at all times. The pressure regulator compensates for engine load by increasing fuel pressure as engine vacuum drops.
The cartridge regulator is serviced as a separate component. When servicing the fuel pressure regulator, insure that the O-ring backup, (3) large O-ring, (4) filter screen, (5) and small O-ring (7) are properly placed on the pressure regulator.
It's located on the fuel injector fuel rail !


Search from over 10 Million Auto Parts

Jul 06, 2015 | 1998 Buick Regal

2 Answers

Fuel pressure 1998 jeep grand cherokee 4.0 L V6


You should have a test port on the Fuel Supply rail, use a tool from a local auto parts "Tool Loaner program" where you can borrow tools for free,w/a deposit of course,then follow the steps provided;

MPI Fuel System Pressure Test

The MPI fuel system used in vehicles equipped with a 4.OL engine employs a vacuum balanced pressure regulator. Fuel pressure should be approximately 55-69 kPa (8-10 psi) lower with the vacuum line attached to the regulator than with the vacuum line disconnected. System fuel should be 214 kPa (31 psi) with the vacuum line connected to the regulator and 269 kPa (39 psi) with the vacuum line disconnected. CAUTION: Some fuel may be discharged when connecting fuel gauge to fuel rail.
  1. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to test port pressure fitting on fuel rail (Fig. 7).
  2. Remove vacuum line from pressure regulator.
  3. Start the vehicle.
  4. Note gauge reading. With vacuum line disconnected, fuel pressure should be approximately 269 kPa (39 psi).
  5. Connect vacuum line to pressure regulator. Note gauge reading. Fuel pressure should be approximately 214 kPa (31 psi).
  6. If fuel pressure is not approximately 55-69 kPa (8-10 psi) higher with vacuum line removed from regulator, inspect pressure regulator vacuum line for leaks, kinks or blockage. CAUTION: Fuel pressure will rise to as much as 655 kPa (95 psi) when the fuel return tine is pinched shut, shut engine down immediately after pinching oft fuel return line.
  7. If fuel pressure is low, momentarily pinch shut the hose section of the fuel return line. If fuel pressure remains low, inspect the fuel supply line, fuel filter, and fuel rail inlet for blockage. If fuel pressure rises replace fuel pressure regulator.
  8. If fuel pressure is above specifications, inspect the fuel return line for kinks and blockage.

Capacity Test

  1. Remove the cap from the pressure test port in the fuel rail.
  2. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to the pressure fitting on the fuel rail (Fig. 7).
  3. Start the vehicle. Pressure should be approxi- mately 214 kPa (31 psi) with the vacuum hose connected to the pressure regulator and 269 kPa (39 psi) with the vacuum hose removed from the pressure regulator.
  4. If the pressure is not to specification, check the following before replacing the fuel pressure regulator:
  • 4a - Inspect the fuel supply and return lines/hoses for kinks or restricting bends
  • 4b - Check the fuel pump flow rate. A good fuel pump will deliver at least 1 liter of fuel per minute with the fuel return line pinched off. If the fuel pump does not pump adequately, then inspect the fuel system for a plugged fuel filter or fuel pump inlet filter (sock). Fuel pump flow rate can be done by connecting one end of an old A/C gauge hose to the fuel test port on the fuel rail and inserting the other end of the hose into a container of at least 1 liter capacity. Run the fuel pump by installing a jumper wire into diagnostic connector terminals D1-5 and D1-6. Be sure to pinch off the fuel return line or most of the fuel will be returned to the fuel tank.

May 19, 2014 | 1996 Jeep Grand Cherokee

1 Answer

Exhaust pipe is blowing out a mist of black smoke


BLACK EXHAUST SMOKE IS A RICH FUEL MIXTURE.CAUSE BY WEAK SPARK IGNITION, FAULTY MAP SENSOR CHECK MAP SENSOR VACUUM HOSE AND ELECTRICAL CONNECTOR BECAUSE BAD MAP SENSOR WILL CAUSE RICH FUEL MIXTURE CHECK THE VACUUM LINE GOING TO FUEL PRESSURE REGULATOR, MAKE SURE FUEL PRESSURE REGULATOR GETTING VACUUM AT VACUUM LINE IF NOT LOOK FOR BROKEN OR DISCONNECTED VACUUM LINE TO FUEL PRESSURE REGULATOR, CHECK FUEL PRESSURE REGULATOR VACUUM LINE IF YOU SEE GASOLINE IN VACUUM DIAPHRAM TO FUEL PRESSURE REGULATOR REPLACE FUEL PRESSURE REGULATOR,CHECK THE EVAP CANISTER IF GAS SOAK IT WILL CAUSE RICH FUEL MIXTURE.

Aug 05, 2011 | 1995 Chevrolet Blazer

1 Answer

Overreving with no power and excessive gas consumption air filter cleaned map sensor replaced fuel pump and filter


usually caused by busted diaphram in fuel pressure regulator allowing fuel to be drawn thru regulator directly to intake manifold. Pull vacuum line off regulator, plug line with golf tee, start car and watch to see if gas comes out of regulator. If yes, turn off car, replace regulator. The regulator sits near the fuel rail on the top of the engine as shown below. I will paste replacement instructions below from autozone.com in case you need to replace the regulator. Please let me know if you have any questions.
jturcotte_421.gif


Removal & Installation

4.2L Engine

  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.

To install:
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.

  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.

Dec 08, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

I have a 2004 Tahoe which has misfire problems (P0300). I changed the plugs, wires, fuel filter and air filter but problem still exist. The 4 plugs on the passenger side continue to file out and become...


Removal & Installation of fuel Regulators on
4.8L, 5.3L & 6.0L Engine To Remove:
CAUTION
Three styles of fuel pressure regulators and fuel rails will be used in this model year. Each regulator has a different "footprint" that consequently changes the size of the receiving port in the fuel rail. The regulator retaining clips are specific to each rail-regulator design and cannot be interchanged.
chevy_aval15_02-04_fuelrail.gif

  1. Remove the engine sight shield.
  2. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
  3. Clean the fuel pressure regulator retainer and the surrounding area.
  4. Remove or disconnect the following:
    • Fuel pressure regulator vacuum line.
    • Fuel pressure regulator retainer.
    • Fuel pressure regulator.
  5. Remove the following parts from the fuel rail:
    • Backup ring (10)
    • Regulator Seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
To Install:
chevy_aval15_02-04_retainer.gif

  1. Make sure the NEW fuel pressure regulator retainer is the right one.
  2. The tabs (1) are used on the straight vacuum port retainer (2), and the E85-straight vacuum port retainer (3).
  3. The angle vacuum port retainer (4) has no tabs. chevy_aval15_02-04_fuelrail.gif

  4. Install the following parts onto the fuel pressure regulator (9).
    • Backup ring (10)
    • Regulator seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
  5. Lubricate the fuel pressure regulator O-rings with clean oil.
  6. Install the fuel pressure regulator and retainer. CAUTION
    Whenever the fuel pressure regulator is removed from the fuel rail NEW O-rings and a NEW retaining clip should be used on reinstallation.
  7. Connect the vacuum line.
  8. Tighten the fuel filler cap.
  9. Use the following to inspect for leaks:
    • Turn ON the ignition, with the engine OFF, for 2 seconds.
    • Turn OFF the ignition for 10 seconds.
    • Turn ON the ignition, with the engine OFF.
    • Install the engine sight shield.
8.1L Engine To Remove:
Fuel pressure regulator vacuum line gm_trk_sub15_fuel_press_reg_vac_line.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of thjs section
  2. Remove the fuel injector sight shield as needed
  3. Relieve fuel system pressure (See: Fuel Pressure Relieving)
  4. Disconnect the fuel pressure regulator vacuum line (A) 8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  5. Clean any dirt from the fuel pressure regulator retainer and the surrounding area
  6. Remove the fuel pressure regulator retainer (I)
  7. Remove the fuel pressure regulator (H) from the fuel pressure regulator housing
To Install:
8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  1. Install or connect the following:
    • Backup ring (J) on the fuel pressure regulator (H)
    • New large O-Ring (K) on the fuel pressure regulator
    • Regulator filter (L) on the fuel pressure regulator
    • New small O-Ring (M) on the fuel pressure regulator
  2. Lubricate the fuel pressure regulator large O-Ring and the small O-Ring with clean engine oil
  3. Push the fuel pressure regulator onto the regulator housing on the fuel rail
  4. Install a new fuel pressure regulator retainer (I)
  5. Install or connect the following:
    • Fuel pressure regulator vacuum line
    • Negative battery cable
  6. Tighten the fuel filler cap
  7. Inspect for leaks using the following procedure:
    • Turn on the ignition with the engine off for two seconds
    • Turn off the ignition for 10 seconds
    • Turn on the ignition with the engine off
    • Inspect for fuel leaks
  8. Install the fuel injector sight shield
  9. Road test the vehicle to check performance
prev.gif next.gif

Sep 02, 2010 | Chevrolet Tahoe Cars & Trucks

1 Answer

Not getting enough fuel .will only go 5 mh and now will idle but stalls when you try to take off


CHECK FUEL PRESSURE IT SHOULD BE 41 TO 47 PSI. IF NOT REPLACE FUEL FILTER..IF DONT HELP FUEL PUMP BAD.IF FUEL PRESSURE GOOD.CHECK VACUUM LINE TO FUEL PRESSURE REGULATOR SHOULD BE GETTING VACUUM IF NOT FIX BROKEN VACUUM LINE TO PRESSURE REGULATOR.IF FUEL PRESSURE REGULATOR GETTING VACUUM THEN THE FUEL PRESSURE REGULATOR IT SELF IS BAD.

Mar 12, 2010 | 1999 Oldsmobile Alero

1 Answer

Leaking fuel pressure regulator


Release fuel pressure by removing fuel pump relay and turning engine over to release pressure. Place a rag to catch any fuel under regulator Fuel pressure regulator has a locking clip pry clip off remove vacuum line pull regulator out with twisting motion,replace fuel pressure regulator install clip connect vacuum line install relay. Check for leaks,your done.

Feb 23, 2010 | 2001 Pontiac Grand Am SE

1 Answer

2001 dodge durango 4.7 fuel pressure flutters during idle


IF FUEL FILTER HAS BEEN REPLACED.FUEL PRESSURE REGULATOR IS GOING BAD OR NOT GETTING VACUUM.CHECK VACUUM LINE GOING TO FUEL PRESSURE REGULATOR.MAKE SURE ITS GETTING VACUUM.IF YOU SEE GAS IN VACUUM LINE TO REGULATOR.REPLACE FUEL PRESSURE REGULATOR.IF ALL IS GOOD FUEL PUMP GOING BAD.

Jan 24, 2010 | 2001 Dodge Durango

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Keeway Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

richard libby

Level 2 Expert

202 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5860 Answers

Are you a Keeway Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...