Question about Keeway Motorcycles

1 Answer

How do you change the engine oil on a leeway matrix 2009 and then top it up with new oil

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 28 Answers

It must have a plug (17 mm) under the right side of the engine and on the same side but on top of the engine there must have the plug to fill up (black plastic with a dipstick).

Posted on Jun 21, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Have a 2009 Ford escape v6 fwd and it keeps over heating what could be the problem ?


Could be the radiator fan not coming on, thermostat stuck, not enough coolant in radiator, engine low on oil,
Hope this helps.

Apr 04, 2015 | 2009 Ford Escape

2 Answers

Car has no power after changing fuses with car on


If your vehicle was running while you
changed a fuse, you may have fried the computer.
Try disconnecting the positive(red side) cable on your
battery. Desconnect it for about 5 or 10 seconds
then reconnect it. This will reset everything.
That is, if you didn't fry the system. You might
want to check that fuse you replaced. For future
reference, only change fuses with vehicle off.

Jun 28, 2014 | 2009 Toyota Matrix

1 Answer

Change bulb in tail light on 2009 matrix


How to change a break light on 2012 Toyota Matrix

Feb 24, 2013 | 2009 Toyota Matrix

1 Answer

What is the procedure for oil change on 2009 range rover sport,and where is the location of the Oil drain plug?


Hi,

Never change your oil while the engine is hot! Let it cool for a few hours, oil can burn you badly.

Be sure you have a safe area to do your oil change. Level, solid ground is a must so that you can safely jack up your car. I also like to put something on the driveway or garage floor underneath the engine in case you spill. Cardboard or a piece of plywood are great for this.
Before you even start to do your oil change, be sure you have everything you need to get the job done.

What You'll Need
  • Ratchet or open end wrench
  • Oil filter wrench
  • Oil catch/recycle container
  • Funnel
  • New oil filter
  • New Oil
  • Clean rag
The first step in an oil change is to get the old stuff out of there. The oil drains out of the oil pan at the very bottom of your engine. The oil is held in by a drain plug that looks like a big bolt at the bottom of the pan.

Before you remove the oil drain plug, be sure that your recycling container is positioned underneath the oil drain. An oil change can be no fun if most of your time is spent cleaning up oil. When you remove the drain plug, let it drop into the top of the recycling container. There's a screen on top that will keep it from dropping into the muck.
Let all of the oil drain out, then replace the drain plug, tightening it to your cars torque specifications (or "snug but not too hard" if you are sans torque wrench.)
Put the cap on the oil recycling container so you can drop it off at a location that accepts used oil -- most full service gas stations accept it.

Next you need to remove your old oil filter. Using an oil filter wrench, turn the filter counterclockwise until it's free. Be careful with it, it's still full of old oil that can spill and make a mess. Some oil filters can be reached from the top, but for most you'll have to be under the car.

With the old oil out and the old filter out of the way, it's time to put the change in oil change. But before you install the new oil filter, you have to prep it. Before you screw the new oil filter into place, lubricate the rubber gasket on the end of the filter with some new oil. Next, fill the new oil filter with oil to about 2/3. It's ok if you go over that amount, it just means you might spill a bit when you screw it on.

Carefully screw the new oil filter into place. Remember, it has oil in it so don't forget to hold it upright. It screws on clockwise. You don't need a wrench to install the new oil filter. Screw it on as tight as you can get it with one hand. Overtightening the oil filter can strip its threads and cause a leak. Of course, not tightening it enough can cause a leak. So screw it on as tight as it will go with one hand, but no more.

Now you're ready to fill the engine with oil. Unscrew the oil fill cap and insert your funnel. I like to buy the 5-quart containers of oil (cheaper) but if you're using single quarts that's fine, too. Check your owner's manual to find out how much oil your engine holds. Pour a little more than 3/4 that amount into the engine. For example, if your car holds 4 quarts of oil, add 3 1/2.
If you're using a 5-quart container of oil, there is a guide on the side that shows how much oil you've put in.
You're not finished yet so don't drive off.

We didn't add all the oil because there may still be a little oil here and there we didn't account for. Check your oil and add more until you're at the right level.
Be sure to put your oil cap back on! Oil spray can cause a fire.

Best regards.

Oct 29, 2010 | 2009 Land Rover Range Rover Sport

1 Answer

How do i turn off check engine light on a toyota matrix 2005 after oil and filter change


The check engine light indicates a need for a scanning with a engine scan tool (OBD-II perhaps).

An oil change will not get rid of this light.

Jul 05, 2010 | 2005 Toyota Matrix

1 Answer

Where is the oil filter?


on most vehicles the oil filter is can shaped and mounted on the engine block, and will be found from under neath of the vehicle to change the oil 1 jack the front of the vehicle and secure it on stands 2 place a collection pan under the vehicle (large enough to hold the vehicles oil capacity) 3 remove the plug on the bottom of the oil pan to allow oil to drain 4 use an oil filter wrench to loosen the oil filter (it will contain oil as well) 5 allow several minutes for oil to drain, the longer the better 6 replace the plug 7 pour some oil into the new filter, and oil the rubber gasket on the new filter 8 replace the filter by hand (do not use filter wrench to tighten) 9 tighten the new filter by hand to one full turn after the gasket touches the engine and no tighter 10 refill from the top of the engine to vehicles oil capacity with recommende weigth of oil note. the engines capacity and the engines capacity with filter differ for the filter will hold oil as well 11 lower the vehicle from jack stands change every 3000 miles when driving in town change every 5000 miles when driving on highway

Jan 09, 2010 | 2009 Toyota Camry

2 Answers

Hello! Where is the oil filter located in 2009 Toyota Matrix


9_8_2012_4_09_58_pm.jpg The oil filter is on the right rear of the engine. The attached photo, viewed from the center rear of the engine shows the oil filter cover, which black, circular, and about 3 inches in diameter. There is a special oil filter socket wrench (64 mm, 14 flats) that mates to the 14 flat spots around the circumference of the filter cover. You can also see on the lower left, a spring loaded tab, ostensibly to prevent the filter cover from unscrewing and falling off.

Note that this is a "cartridge" filter, so what you are seeing in the photo is the filter cover, not the filter itself. After unscrewing the cover, the actual filter will be inside the cover when you remove it. The new cartridge filter should come with a new O-ring, which you will place on an indentation on the filter cover. Be sure to liberally lubricate the new O-ring with clean oil. Then insert the new filter into the cover, and screw the cover back into the engine. Be very careful that the O-ring stays in place in the cover indentation, and does not slip out to the cover flange. This happened to me once, and even though the cover was properly torqued, when I started the engine, the O-ring popped out and oil sprayed everywhere. The oil filter cover flange should mate right up against the engine, without the O-ring (or anything else) in between. I don't particularly like this design because it makes oil changing a little more tricky than the old fashioned spin-on filters.

I raised the front wheels about 5 inches using ramps. Without raising the vehicle, I think it would be extremely difficult to get under there to access the filter.

Aug 09, 2009 | 2009 Toyota Matrix

1 Answer

Audi A5 engine oil top up


Audi cars do not use much oil as far as I know.A new engine which is not warned together can take some oil of course.Make sure that you use the proper oil type specified by the manufacturer.Try to change the oil and filter completely,then measure the oil consumption.Should not be more then 1 liter on 10000kms.

Jul 10, 2009 | 2009 Audi A5

2 Answers

How to I replace the oil filter on a 2009 Toyota Camry V6 engine?


Under the engine in the front you will see an aluminum cover.There is a square hole that fits a 3/8 ratchet remove this first.The new filter comes with a drain adapter that snaps in the hole under the cover.This lets the oil in the housing drain.Then take a oil filter cup wrench or a big channel lock to twist of the larger portion.Then change the filter and o-ring and reinstall.Make sure the o-ring on the square drive cover is there also

Nov 30, 2008 | 2004 Toyota Camry

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Keeway Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

richard libby

Level 2 Expert

209 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5948 Answers

Are you a Keeway Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...