Carbon brushes - 2002 BMW F 650 CS Scarver

Installing a carbon bush on a Stannah 420 stair lift requires some technical knowledge and experience, as it involves working with electrical components. If you are not familiar with stair lift maintenance and repair, it's best to contact a professional technician or Stannah service representative to ensure the proper installation and safety of the carbon bush.
However, if you have the necessary skills and knowledge, follow these general steps to fit a carbon brush to a Stannah 420 stair lift:

1. Safety First: Before starting any work, ensure the stair lift is turned off, and the power supply is disconnected to avoid any electrical accidents.
2. Access the Motor Compartment: Open the motor compartment of the Stannah 420 stair lift. This is usually located under the seat or at the base of the unit. You may need to remove some screws or panels to access the motor area.
3. Locate the Carbon Brushes: The carbon brushes are small, rectangular-shaped components made of carbon and graphite, and they make contact with the motor's armature. Look for the existing carbon brushes, which might have worn down or need replacement.
4. Remove the Old Brushes: Carefully detach the old carbon brushes from their holders. This may require gently pulling them out or undoing some clips or screws that secure them in place. Take note of how the old brushes were positioned so you can properly install the new ones.
5. Install the New Carbon Brushes: Insert the new carbon brushes into their respective holders and secure them in place as per the manufacturer's instructions. Make sure they are positioned correctly and have good contact with the motor armature.
6. Reassemble: Once the new carbon brushes are in place, reassemble the motor compartment by putting back any removed panels or covers and tightening any screws that were undone.
7. Test the Stair Lift: Reconnect the power supply and turn on the stair lift. Test the unit to ensure the new carbon brushes are working correctly and that the stair lift operates smoothly.
8. Regular Maintenance: Carbon brushes wear down over time, so it's essential to perform regular maintenance and inspections to identify when they need replacement. The frequency of replacement depends on the stair lift's usage and other factors.

Again, if you're unsure about any part of this process or lack experience with stairlift maintenance, it's best to seek professional help to ensure the job is done safely and correctly.

This company

Replacement Emerson Carbon Brushes - Repco Inc

https://www.repcoinc.com > brushes > Carbon_Brushes...
Repco supplies replacement carbon brushes for Emerson motors. Our Emerson carbon brush experts help you find the right product for your particular ...

..

Hello, D_curry751 -

It will help in directing to the best source for you for purchasing carbon brushes for your Hoover washing machine, if you indicate the country where you reside. You can add that information in the Comment box.

Note: Questions come into Fixya.com from all over the world and it can be hard to guess what the best resource for the right information.

Without knowing the country of your residence, I did find Hoover washing machine carbon brushes sold online (USA web sites):

eBay:
https://www.ebay.com/b/Hoover-Washer-Dryer-Carbon-Brushes/99697/bn_5864242

Amazon:
https://www.amazon.com/Genuine-Washing-Machine-Brushes-09036062/dp/B00EO4QZAW

These are United Kingdom websites selling Hoover washing machine carbon brushes:

eBay, United Kingdom:
https://www.ebay.co.uk/b/Hoover-Washing-Machine-Dryer-Carbon-Brushes/99697/bn_3272613

BuySpares, United Kingdom:
https://www.buyspares.co.uk/washing-machine/hoover/carbon-brush/catalogue.pl?path=495970:496360,45786:495976&refine=carbon+brush

PartMaster, United Kingdom:
https://www.partmaster.co.uk/hoover/washing-machine/carbon-brush/catalogue.pl?shop=hoover&path=45786&refine=carbon%20brush

Remington Pole Saw Carbon Brushes
If you're Remington Pole Saw is slowing down, throwing sparks, overheating or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature!
Remington carbon brushes on E-bay Search for:
Remington Pole Saw 8 AMP Carbon Brush

Remington Pole Saw Carbon Brushes
If you're Remington Pole Saw is slowing down, throwing sparks, or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature!
Remington carbon brushes on E-bay Search for:
Remington Pole Saw 8 AMP Carbon Brush

Remington Pole Saw Carbon Brushes
If you're Remington Pole Saw is slowing down, throwing sparks, or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature!
Remington carbon brushes on E-bay Search for:
Remington Pole Saw 8 AMP Carbon Brush

hi try potts in derby babbington lane ,very help full

Generator replacement brush notice:
1, from the model and material needs and the original brush.
2.It is best to grind the new brush to the Radian size of the old brush.
3. pay attention to adjust the brush grip pressure.
4. the carbon brush size should be equal, not too big or too small. The carbon brush is not subject to force in the process of placement.
5. pay attention to the carbon brush and armature to have obvious contact, do not push the carbon brush in.


Generator brush replacement method:
1, the first with a special wrench loose brush braid fastening screws, loose fastening screws should not be loosened excessive, to prevent screw loosening and falling off.

2, take off the carbon brush braid, the carbon brush and the pressure-equalizing spring at the same time. When installing a carbon brush, put the brush into the brush grip.
3, then press the equalizing spring.
4.Use special wrench to fasten the brush and braid to fasten the screw. When fastening the screw, it is not necessary to exert too much force to prevent the screw from being damaged.
5. Check that the brush moves freely in the brush grip, and the spring can be pressed in the center of the brush.

RE AEG PH 38 Brushes go to local hardware storeinthe miscelleanous everything aisle and look or a SKIL brush set exact size match $4.50 US cost I fixed mine today. Brush holders another issue

Try RepairClinic.com