Question about 2003 Yamaha YZ 125

1 Answer

My 2003 yz 125 hesitates when you give it gas.It does it every time you switch gears.You have to give alot of gas to straighten it out.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

It is one of a few things causing it to flail in the lower end, 1: your fuel oil mixture isnt lean enough.. 2: you need a higher spaking plug.. 3: your carburetor float level is out or 4: there is a slight break in the ignition spak line which would cause it to spark very weak until maximum accelleration is reached

Posted on Jun 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1976 yamaha yz 125 not shifting properly.not staying in gear


If it does stay in gear when barely throttled but does not stay in while under load, the engagement dogs on the gears(inside the engine) are bad and the engine will need to come apart to repair it.

Nov 17, 2014 | 2003 Yamaha YZ 125

1 Answer

Can a 2003 yz 125 throttle cable fit on a 2010 yz 85


From my understanding the cable on the 125 is alot longer and where it connects to the carb. Its a different size.

Aug 29, 2014 | Motorcycles

1 Answer

I have a 2000 yz125 and when I shift into 3rd gear and give it gas it kicks it back down to 2nd gear. sometimes I cant get it to shift into 2nd gear. any ideas? thanks


I am presuming you are giving the gear lever a positive shifting motion when changing gears.
If the gear lever is completely tight on the gear shift shaft and the toe of the lever does not touch the engine sidecover when changing up, you may have a worn roller shift lever or loose screws holding this mechanism in place. See the exploded view diagrams of the SHIFT CAM and SHIFT FORK with all part names and numbers on the link below.
Cheers!

http://www.cmsnl.com/yamaha-yz125m1-2000_model10887/partslist/

Mar 04, 2011 | 2003 Yamaha YZ 125

2 Answers

I have 2003 yz 125 it runs teriffic and shift's grate 1-5 but it wont go in to 6st gear . any ideas


Well - you will first have to buy an earlier model to get into 6th gear. The 2003 YZ 125 is a 5 speed transmission. There's nothing wrong with your bike.

Feb 17, 2011 | 2003 Yamaha YZ 125

1 Answer

Reccommended gear oil for 2003 Yamaha YZ-125


85\90 transmission oil such as bel ray, motul or yamalube

May 26, 2010 | 2003 Yamaha YZ 125

1 Answer

Gear grinding in first gear withoutany visible damage 1992 yamaha yz 125


look to see if the clutch is burned out thats what happened to my ttr 125 and we change the clutch and it was fine then hope this helps

Sep 07, 2009 | 2003 Yamaha YZ 125

1 Answer

I have a 2003 yamaha ttr 125. At times it acts like it isn't taking gas and five minutes laterit is running fine. Sometimes it will even stall out on me.


3 things,

carb check
float bowl check
and clutch check.

these, if not set right will give out what you are experiencing.

you may refer to the manual on the default / recommended settings depending on the type of gas you are using.

regards, safe trails.

Jun 30, 2009 | 2003 Yamaha YZ 125

1 Answer

1994 Buick Skylark. Lot of hesitation and jerking, power locks


HI MY NAME IS JUAN:
I HAVE A 93 BUICK SKYLARK CUSTOM
AND I HAD THE SAME HESITATION.
I CHAGED GAS FILTER, AIR FILTER, AND USE SEA FOME IN MY GAS TANK AND USE IT ALSO TO CLEAN THE INTAKE SYSTOM, AND IT HELPED ALOT. TWO MONTHS DOWN THE LINE HADE THE SAME HESITATION AND IT WAS ONE OF THE INISION COIAL PACK WAS NOT GIVING THE ELETRICAL SPARK TO THE PLUG. I CHECK IT BY PULLING THE CABLE OFF THE SPARK PLUG WITH THE CAR RUNNING AND FOUND THE ONE THAT WAS NOT GIVING SPARK. I REPLACED THE PACK FOR THAT CILINDERS PLUG AND THE PROBLEM WAS GONE.
HOPE THIS CAN HELP YOU.

Jun 17, 2009 | Buick Skylark Cars & Trucks

1 Answer

Will main clutch casing fit yz 125 2001 from 1997?


Hey Ryan! Long time since hearing from you.

When you say "main clutch casing" do you mean the right side cover for the gearbox or do you mean the primary driven gear (AKA "clutch basket") that the clutch boss (AKA "clutch hub") and all the clutch plates fit into?

If you mean the right outer casing > they are slightly different, '97 pn 4JY-15431-10-00 and 2001 pn 4JY-15431-12-00. The entire clutch is the same from 1997 through 2001.

Jun 07, 2009 | 2003 Yamaha YZ 125

1 Answer

2003 YZ 125 RUNS AND ONLY STAYS IN FIRST GEAR


This is a shift fork or shift drum issue inside the transmission.


please rate this solution

Feb 21, 2009 | 2003 Yamaha YZ 125

Not finding what you are looking for?
2003 Yamaha YZ 125 Logo

Related Topics:

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

D. E. Hev

Level 3 Expert

1187 Answers

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...