Need torque values for left valve cover on my R1200GS

Question edited for clarity.
Question moved to model category.

Torque Specifications - Honda CRF250X Owner's Manual ...

ManualsLib https://www.manualslib.com > manual > Honda-Crf250x

Honda CRF250X Manual Online: Torque Specifications. ENGINE Torque Item N•m kgf•m 1 Cylinder head cover bolts 10 1.0 2 Exhaust pipe joint nuts 21 2.1 3 10 ...

Crankcase Torque Spec.?? - CRF250R & RX

ThumperTalk https://www.thumpertalk.com > forums > topic > 8357...
Nov 5, 2010 - 12nm, 9ft lbs or 108"lbs. Don't use loctite on the case bolts. Use some blue loctite on the kick start bolt, that usually the one that comes ...

torque specs please service manual guys - CRF250X
Oct 28, 2009
Clutch cover and Crank cover Bolts/torque? - ThumperTalk
May 17, 2006
Bolt torque specs - CRF250R & RX - ThumperTalk
Aug 10, 2007
bottom end torque specs - CRF250R & RX - ThumperTalk
May 20, 2009
More results from www.thumpertalk.com

Left side cover torque specs 2005 crf 250

CRF's Only https://crfsonly.com > forum > viewtopic
Feb 25, 2012 - Hey fellow red riders I'm having to change my left side cover and can't find the torque specs for the left side cover bolts and if the ...

Torque Spex - CRF's Only Forums
Jun 21, 2007
CRANKCASE BOLTS TORQUE - CRF's Only Forums
Apr 18, 2017
Torque Specs 2006 CRF250x ? - CRF's Only Forums
Jul 1, 2009
Washers and Bolt Torque - CRF's Only Forums
Apr 9, 2017
More results from crfsonly.com

HONDA CRF250X

Honda http://owners.honda.com > 2005 > 2005_crf250x
side cover bolt (8). 6. Install the collar (7) and seat bolt (9) tighten the bolt to the specified torque: 20 lbf·ft (26 N·m, 2.7 kgf·m). Servicing Your Honda.
180 pages ..

The torque specification for the cylinder valve cover stud/bolt on a 2007 Honda Accord 2.4L VTi is 7.2-8.1 lb-ft (10-11 Nm).
As for replacing the broken stud, it depends on how the broken stud is located and the extent of the damage. If the broken stud is easy to access, it may be a simple matter of unscrewing the old one and putting a new one in with the correct torque specification. However, if the broken stud is difficult to access or if it has caused damage to the threads, it may require a more complex repair. In some cases, it may be necessary to drill out the old stud and tap new threads or to use a helicoil insert to repair the damaged threads.
It's important to note that over-tightening the valve cover bolts/studs can lead to damage or deformation of the valve cover or gasket, and under-tightening can lead to oil leaks. So, it's crucial to torque the bolts/studs to the specified torque value.

Wildly varying advice. I would use the lower amounts. They are not under a lot of pressure and you don't want to compress the new gasket too much.

https://www.google.com/search?q=toyota+camry+2.4+valve+cover+bolt+torque+specs

..

25-35 ft lbs

Here are the torque specifications for a 2005 International DT466E valve cover:
• Injector holds down on 120 in-lb
• Valve cover 13 ft-lb
• Valve lash 0.025 cold in-ex

hi valve covers are never more the 8 to 10 nm newton meters start in the middle one across from each other then criss cross one on the top right then to the left bottom ,then top left,right bottom work your way out till they are all done cant be too tight or it will squish the gasket and cause leaks danny

15 foot pounds... no pattern is given for such a low torque value

Felpro brand gaskets are the best in the world, not sure about the intake, if it is in the way then yes remove it.

Rocker cover cap nuts are torque to 22 / 26 Nn and the 6 mm threaded valve cover nuts should be 10 - 20 Nm
Ride Safe
Bike-Doc

Please mark this as useful (if it has been!!)