Reset key fob - BMW Motorcycles

limited info generic answer check and test battery -- most likely the key fob itself is failing you can have some one test fob or get another fob[s] and have programmed

The key fob will need to be reprogrammed to the vehicle since when the battery was replaced in the key fob, the key was reset. This is why nothing is working with the key fob. After replacing the battery in the key fob remote, you will need to reprogram the remote to the vehicle

Most people think you have to program the key fob to match the car. In fact, the opposite is true - you have to program the car to respond to the key fob. You'll need to have all your key fobs handy and follow some instructions precisely.
https://itstillruns.com/reset-kia-after-battery-disconnected-7650450.html

To better answer your question it helps to know if the key fobs worked before and just stopped working, or if you bought a new key fob.

If you bought a new key fob you must program it to your vehicle. Here are the key fob programming instructions for a 2006 Chevy Monte Carlo:

NOTE: 2O11 & newer vehicles must be programmed by an automotive locksmith or dealership.
PROCEDURE #1
THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

1. Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
2. Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
3. Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
4. Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
5. Repeat step 4 to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
6. To exit programming mode turn ignition OFF, remove key and test all remotes.

PROCEDURE #2
THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

1. Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
2. Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
3. Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
4. Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
5. Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
6. To exit programming mode turn ignition OFF, remove key and test all remotes.

If your key fob worked previously and it just stopped working here are a few key fob fixes to try:

Change the battery
Batteries don't last forever, you'll be surprised how often it's just a dead battery! Search our YouTube channel on how to change a key fob battery for your specific year, make, and model!

Wipe the board
The board inside your remote can get a lot more filthy than you think! When the board is dirty it can prohibit the contact to the circuit board when you push down on the button. Simply wiping the circuit board off can make your key fob like new again!

The old car battery reset trick
I know this sounds absurd, but it works sometimes and is worth trying. If you exhausted all of the options above, disconnect both terminals on your car battery for 10 minutes. Then reconnect them and try your key fob. This has worked for many people and I have no idea why.

t might be time for a new key fob! No need to dread over the expensive costs of a new key fob, at Keyless Entry Remote Fob Inc., you can get a refurbished one for a very affordable price! You won't even be able to tell the difference. Just search your vehicle make, model, and year to purchase a key fob or give us a call at 402-671-5100.

battery may be flat in the fob or the vehicle has forgotten the code for the fob. and will need resetting. change the battery use the key to open the door put key in the ignition. ( fob Ir old type leave fob off the key) turn to number 2 and press fob till doors lock and unlock. then its reset. dont be worried if the alarm goes off while doing this it will go off when the code is restored. if you have 2 fobs you will need to rest that one to.

The remote key fob battery replacement:

There are a few things you can do to get your key fob working like new again:

1) Wipe the board
The board inside your remote can get a lot more filthy than you think! When the board is dirty it can prohibit the contact to the circuit board when you push down on the button. Simply wiping the circuit board off can make your key fob like new again!

2)Get it checked
Go to your local hardware store like AutoZone or Oreilly's. They usually have a RF frequency tester. This little gadget will let you know if your key fob is sending a signal. If it is, you may need to reprogram your key fob to your vehicle

3)The old car battery reset trick
I know this sounds absurd, but it works sometimes and is worth trying. If you exhausted all of the options above, disconnect both terminals on your car battery for 10 minutes. Then reconnect them and try your key fob. This has worked for many people and I have no idea why. If you do, please comment below to explain.

4)New fob!
It might be time for a new key fob! No need to dread over the expensive costs of a new key fob, at Keyless Entry Remote Fob Inc., you can get a refurbished one for a very affordable price! You won't even be able to tell the difference. Just search your vehicle make, model, and year to purchase a key fob or give us a call at 402-671-5100.

Hi,
Kindly submit the question under 1999 Toyota Avalon section on the website by clicking this link so that the best car experts can view and post a solution to the problem.

Thanks for using FixYa.

hi you can do this but you will have to have a key that does not have a remote/fob on it ( basically just go get one cut cheaply ) then to reprogram keys/key fob's first using the key without fob, turn ignition on ( do not turn over, just to position 2) then lock drivers door with other key ( do not use fob, just the key itself with fob now complete the following within 30 seconds within 5 seconds( of locking the car) press the unlock button on the first key once ( this programs that key as key memory1) the indicators should flash once to indicate signal received wait 5 seconds then press unlock on key fob vehicle should then unlock meaning key fob has been programmed and programming ended open door turn ignition off , and that's it, it should work if you have more than 1 key with fob, do the same as above but instead of pressing unlock once, you do it twice, if third key 3 x if fourth key 4 x etc etc,

The only reset is if the key fob and the receiver get out of sync, to check that be out side of the car doors closed and unlocked. Press both lock and unlock buttons on the remote (key fob) at the same time if the doors lock and unlock that was your problem. It could be the battery it could be the key fob or the receiver.