Motorcycles Logo

Related Topics:

andrew kriegh
andrew kriegh Posted on Oct 08, 2013
Be the first to answer

Will not start clicking noise

When i hook it up directly to the pos and neg and press start it just clicks kinda fast and quiet

Answer This Question

5 Related Answers

goalie39

Ed

  • 479 Answers
  • Posted on Apr 13, 2009

SOURCE: Bike won't start/clicking coming from starter relay

Have you tried charging the battery or jumpstarting it with another battery?

Ad

Anonymous

  • 78 Answers
  • Posted on Jun 25, 2009

SOURCE: Bmw R1200cl won't start battery fully maintained

A fully maintained battery does not guarantee a good battery. The fast click is almost always caused by insufficient power. If you've checked the connections, try jumping from another 12v battery. If that gets the crank to turn, have the battery load-tested, or just replace the battery.

A new battery installed by you is still going to be far cheaper than having a mechanic diagnose this, and if a new battery doesn't do it, it's very likely the starter getting old, dragging, and drawing more power than the battery can deliver.

Anonymous

  • 434 Answers
  • Posted on Jul 01, 2009

SOURCE: WHEN PRESSING IGNITION,OIL LIGHT COMES ON, NOTHING ELSE.

Sounds like the starter relay is bad. Lay a screwdriver across the two poles and see if it starts. If the bike turns over, that's your problem

Anonymous

  • 345 Answers
  • Posted on Aug 10, 2010

SOURCE: loud clicking noise coming from under seat. looks

This is usually caused by not enough voltage in your battery, replacing the battery should solve the problem. Not enough power to the starter motor, will make the soleniod click rapidly.

Anonymous

  • 738 Answers
  • Posted on Feb 27, 2011

SOURCE: my ignition fuse keeps popping on my 1100. I have

The fuse should only connect to the pos side of the battery

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
2answers

Someone hooked jumper box up backwards on van and tried ti start it it ran great before that after it wouldn't start at all changed the computer now it starts runs a few mins then shuts off what could it...
You will have to take it to the Dealer. You may have burnt out or the "Control Module" needs to be replaced or reprogrammed. Make sure the battery has not reversed polarity also.
Read full answer
Feb 13, 2015 • Cars & Trucks
1helpful
1answer

I replaced the battery terminal cable ends. Now the car will not start, There is a clicking noise from the starter.
Bad connection on cable ends or where they connect to battery. Quick check is if you have a good set of jumper cables, use the jumper cable as a replacement for what maybe the defective one. Hook negative cable good to battery neg. post and then put other side on neg cable to engine ground on block. See if it cranks, if it does than the trouble is on the neg. cable. If not then put positive cable on pos. post of battery. Then put other side of pos. cable on the starter post, try to start. If it cranks then the trouble is on the pos side of cable. Hope this helps.
Read full answer
Nov 16, 2013 • 1996 Geo Prizm
0helpful
2answers

How to hook up 2 new batteries
hook them up in parallel, pos to pos, neg to neg from one battery to another, then pos cable to battery prs and ground cable to neg battery
Read full answer
Jul 29, 2010 • Renault Fuego Cars & Trucks
0helpful
1answer

92 nighthawk LED blinker problems.
Honda always grounds the turn signals separately (usually a green wire)not directly to the frame.Not hooking up the running light should not effect anything except forward visibility to other motorists. If you have a two prong flasher relay, go get a cheap flasher relay ($5-$10) and replace it. The only problem I have ever heard of when switching to LED turn signals is a flicker / fast flash instead of a normal slow flash. This is remedied by adding diodes to the wires.
Read full answer
Jun 30, 2010 • 1985 Honda CB 700 SC Nighthawk
2helpful
2answers

Need to charge 12v car battery
Hello,

If battery is out of the vehicle, connect positive lead to positive terminal and negative lead to negative terminal.

If battery is in the vehicle, the proper way to connect leads depends on if it's a negative-grounded or a positive-grounded vehicle.

Here is a link to the manual for this charger.
Click where it says "Get This manual" (it's free).

Scroll down to pages 4 and 5 and it give detailed instructions on the proper way to connect leads and a lot more. It's a good manual to keep for future use.

I hope this helps.

http://powertool.manualsonline.com/manuals/mfg/schumacher/se520ma_se5212a_se1275a.html



Read full answer
Sep 22, 2009 • Schumacher & Fast Charge Starter Charger
0helpful
2answers

Baja 90 is difficult to start
Check for spark using a new spark plug and clean the carburetor / air filter.
Read full answer
Aug 01, 2009 • 2005 Qianjiang QJ150
0helpful
1answer

Jl audio 500/1 amp low ohm light at high volume
I would try running the subs in parallel. Pos to Pos Dual Voice, Neg to Neg Dual Voice. Then Run + to + stereo - to - stereo on both channels.
So you have + and - running to one channel and + and - running to the other channel.
Also your LPF filter could be set too high.
Read full answer
Feb 07, 2009 • Jl Audio 500/1 Car Audio Amplifier
2helpful
1answer

I bought a 500/1 jl audio amp and also a w7 10 sub
if its cutting off and right back on then check your ground and your power wire makes sure both are connected good and none of your fuse's are blown, either that or you got a wire hooked up backwards in the sub.. but my guess is that the sub is hooked up wrong... that sub should be hooked up in a series or in parallel,

ok if your running just one speaker, it should be hooked up like this and 2 speakers are a different way...

this is parallel :pos to pos , neg to neg, then one wire coming from pos on sub to pos on amp then neg on sub to neg on amp but bridge the amp on your amp should be 2 pos and 2 neg in two different channels take the pos off the sub into the pos on 1 channel and then the neg from sub to the neg on the other channel,

this is series : on the sub it will go pos to neg then the other neg and pos will go to the amp, but make sure the pos and neg r on different sides of the sub, dont hook them both to the same coil

if your need more help give me your email and ill send you a pic of how to do it...


Read full answer
Aug 12, 2008 • Jl Audio 500/1 Car Audio Amplifier
0helpful
1answer

Help
one wire to pos to amp plus to speaker one. now secound speker use neg. to neg. on amp. now take a speaker wire and hook up the remaining neg. post. on the spekers. This will run them in seris like my 4000watt rms amp at a 2 ohm load. Make sur your speakers can handel the rms load of amp. If not they will blow.
Read full answer
Jul 19, 2008 • Car Audio & Video
Not finding what you are looking for?

View Most Popular

Motorcycles

Related Question

Someone hooked jumper box up backwards on van and tried ti start it it ran great before that after it wouldn't start at all changed the computer now it starts runs a few mins then shuts off what could it...

  • Cars & Trucks

72 views

Ask a Question

Usually answered in minutes!

Popular Questions

What is this relay for?

1995 Yamaha FZR 600

What cause the voltage regulator to smoke every time you put the put the battery ?

1992 Yamaha FZR 600

Yamaha FZR 600 not charging correctly with the lights on

1991 Yamaha FZR 600

My FZR600 won't start. No mods, all stock. I got

1989 Yamaha FZR 600

How to remove a link from a motorcycle chain

1994 Yamaha FZR 600

Top Yamaha Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

littlewheel

Level 2 Expert

122 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
XJ700XS 1986.PDF. user-manual-1994 FZR...

1994 Yamaha FZR 600

PDF Manual
Yamaha_FZR600_chapter_3_ pt1.pdf....

1992 Yamaha FZR 600

Loading...