Motorcycles Logo

Related Topics:

jim mcfann
jim mcfann Posted on Sep 23, 2013
Be the first to answer

Replace side mirror 2004

How do i tighten right side mirror

Answer This Question

5 Related Answers

Anonymous

  • 405 Answers
  • Posted on Dec 28, 2008

SOURCE: 2004 passenger side mirror replacement

Not difficult if you know how to remove your door panel, most require that. then three nuts and a plug.

Ad

Anonymous

  • 840 Answers
  • Posted on Feb 02, 2009

SOURCE: passanger side mirror replacement on 04 dodge ram 1500?

very easy take the mirror inside cap off if you can not get to the 3 bolts then you will have to take trim panel off to take trim panel off look for plastic caps take them out and unscrew them then pop out the bottom of the door and pop the sides out then lift up and out should be loose enough for the bolts now/ 10mm bolts 3 Please rate my response thank you very much

Anonymous

  • 1986 Answers
  • Posted on Sep 29, 2009

SOURCE: Driver Side Mirror

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Anonymous

  • 1986 Answers
  • Posted on Sep 29, 2009

SOURCE: driver side mirror 2004 Pontiac Grand Am

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Anonymous

  • 1986 Answers
  • Posted on Sep 29, 2009

SOURCE: Right side mirror housing is broken,need to replace.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

I have a 2003 4 runner and the base is loose , how do I tighten it?
Get inside the door and tighten the bolts or screws in the mirror
Read full answer
Apr 24, 2016 • 2003 Toyota 4Runner
0helpful
1answer

How to repair a loose driver side mirror without replacing it?
I would unscrew the 3 screws and take the mirror out, to try and see why theyre not holding it properly. maybe use epoxy to fix the broken bracket and then screw the mirror back on.
Read full answer
Nov 25, 2017 • 1998 Toyota Sienna
0helpful
1answer

Relace side mirror
Remove door panel,unplug mirror wiring and remove nuts that hold on mirror.
Read full answer
Sep 10, 2012 • 2004 Dodge Ram 2500
1helpful
2answers

Please describe how to replace a 2004 focus wing mirror
You have to remove the sail cover that's on the opposite side of the mirror. It is held on by just some plastic lips on the edges. Pry off carefully. There is one speed nut at the very front of the mirror and one large nut in the center. That's it. Don't drop the big nut into the door panel.
Read full answer
Jan 01, 2011 • Ford Focus Cars & Trucks
3helpful
1answer

How do I change side mirrors
Hello, the door outside mirrors are stud mounted to the door filler. The mirror glass face may be replaced by placing a piece of tape over the glass then breaking the mirror face. Adhesive back mirror faces are available. Left side flat and right side convex mirror faces must be replaced with the same type mirror face when surfaced.
  1. Remove the door trim panel.
  2. Remove the upper trim panel.
  3. Remove the sound absorber.
  4. Remove the (3) nuts.
  5. Remove the control cable from the upper trim panel.
  6. Remove the filler and mirror.

INSTALLING THE NEW MIRROR:
  1. Place the filler over the studs on the mirror.
  2. Install the control cable through the filler and connect to the upper trim panel.
  3. Install the (3) retaining nuts and tighten to 42-72 inch lbs. (4.7-8.1 Nm).
  4. Install the sound absorber, upper trim panel and trim panel.
Thanks
Read full answer
Jul 28, 2010 • 1996 Chevrolet S-10 Pickup
1helpful
1answer

Replacing passenger side mirror on 2004 Grand Cherokee' Don't know whether or not heated and how many screws there are.
Your fuse box will tell you if it is heated or not, on the right side under the hood, breaker box, heated mirror, the plastic cover inside the car behind the mirror pops off exposing a few bolts, it will drop the mirror, it is heavy, so don't let go. The wires have to be disconnected inside the door. Hope this helps.
Read full answer
May 06, 2010 • 2004 Jeep Grand Cherokee
2helpful
1answer

How do I replace a side mirror chevy corsica?
Please don't forget to rate....thanks:


Removal & Installation The door outside mirrors are stud mounted to the door filler. The mirror glass face may be replaced by placing a piece of tape over the glass then breaking the mirror face. Adhesive back mirror faces are available. Left side flat and right side convex mirror faces must be replaced with the same type mirror face when surfaced.
  1. Remove the door trim panel.
  2. Remove the upper trim panel.
  3. Remove the sound absorber.
  4. Remove the (3) nuts.
  5. Remove the control cable from the upper trim panel.
  6. Remove the filler and mirror.
To install:
  1. Place the filler over the studs on the mirror.
  2. Install the control cable through the filler and connect to the upper trim panel.
  3. Install the (3) retaining nuts and tighten to 42-72 inch lbs. (4.7-8.1 Nm).
  4. Install the sound absorber, upper trim panel and trim panel.
Read full answer
Mar 06, 2010 • 1996 Chevrolet Corsica
4helpful
1answer

Remove/replacing side view mirror on a jeep grand cherokee
    Remove the Old Mirror
  1. Step 1 Disconnect the negative battery cable before you take off the grand Cherokee front door trim panel. Remove all screws and clips.
  2. Step 2 Detachthe window trim cover screw, and control lever screw beforedisconnecting the entire mirror trim cover. Remove the rubber coverinside the mirror cover, and disconnect the electrical wire.
  3. Step 3 Remove three nuts from the power mirror using a Torx® star-shaped screwdriver.
  4. Step 4 Pull out the outside rear view mirror. Guide the power wire through the hole in the door.
    5. Install the New Mirror
  5. Step 1 Replace the old mirror. Put the new power mirror in place. Push the new wiring through the hole in the door.
  6. Step 2 Install and tighten the three retaining screws you took off when removing the old mirror.
  7. Step 3 Connect the power mirror wiring to the connection located on the door panel. Replace the rubber cover and interior mirror cover.
  8. Step 4 Put the front door trim panel back in place by securing all clips and tightening all screws.
  9. Step 5 Connect the Subaru Outback's battery cable to restore the power.

i will recommend i site where you will get all the information you need to remove and replace your side mirror
http://www.wjjeeps.com/mirrors.htm
Read full answer
Sep 10, 2009 • 2004 Jeep Grand Cherokee
15helpful
2answers

Replacement of the side reaerview mirror on a
so you don't need to change the housing, but just the panel the mirror sits on right? If you mean the entire unit, then you'll need to remove your door panel (screws are by the door handle, arm rest, under door and side of door) and remove the cover adjacent to your mirror to remove the bolts to remove the mirror.

If it's just the back and the mirror, you'll need to angle the mirror until you can see the release clips on the back of the panel that mounts it to the housing (Pivot Point)... be very careful as the clips can easily break....
Read full answer
Aug 10, 2009 • 2004 Dodge Ram 2500
0helpful
1answer

Problem with right signal mirror
plug in disconnects on r/s bottom kick panel, need to remove 3 bolts, remove mirror on passenger side. carefully pop mirror out, the eletronic motor behind the mirror has to pieces that bolts together, the gasket is no good. you can silicone around the mating surfaces, or replace motor
Read full answer
Mar 03, 2009 • 2004 Ford Freestar
Not finding what you are looking for?

View Most Popular

Motorcycles

Related Question

I have a 2003 4 runner and the base is loose , how do I tighten it?

  • 2003 Toyota 4Runner

66 views

Ask a Question

Usually answered in minutes!

Popular Questions

MANUAL SERVICE

1998 BMW F 650 Strada

Cant find the fuse box on a bmw r1200gs motorcycle

BMW Motorcycles

Bmw r1100rt will not start. lights etc come on put

1998 BMW R 1100 RT (ABS)

I have a 99 R1100RT and the ABS lights keep

1998 BMW R 1100 RT (ABS)

Can I reset the maintenance reminder light on my k1600gtl

BMW Motorcycles

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
2005 K1200R 1st.pdf. user-manual-2005...

2005 BMW K 1200 GT

PDF Manual
K1200LT_Comsystemmanual.pdf....

2002 BMW K 1200 LT

Loading...