1998 cr250 bottomend case bolt torq specs

Question edited for clarity.
Question moved to model category.

Torque Specifications - Honda CRF250X Owner's Manual ...

ManualsLib https://www.manualslib.com > manual > Honda-Crf250x

Honda CRF250X Manual Online: Torque Specifications. ENGINE Torque Item N•m kgf•m 1 Cylinder head cover bolts 10 1.0 2 Exhaust pipe joint nuts 21 2.1 3 10 ...

Crankcase Torque Spec.?? - CRF250R & RX

ThumperTalk https://www.thumpertalk.com > forums > topic > 8357...
Nov 5, 2010 - 12nm, 9ft lbs or 108"lbs. Don't use loctite on the case bolts. Use some blue loctite on the kick start bolt, that usually the one that comes ...

torque specs please service manual guys - CRF250X
Oct 28, 2009
Clutch cover and Crank cover Bolts/torque? - ThumperTalk
May 17, 2006
Bolt torque specs - CRF250R & RX - ThumperTalk
Aug 10, 2007
bottom end torque specs - CRF250R & RX - ThumperTalk
May 20, 2009
More results from www.thumpertalk.com

Left side cover torque specs 2005 crf 250

CRF's Only https://crfsonly.com > forum > viewtopic
Feb 25, 2012 - Hey fellow red riders I'm having to change my left side cover and can't find the torque specs for the left side cover bolts and if the ...

Torque Spex - CRF's Only Forums
Jun 21, 2007
CRANKCASE BOLTS TORQUE - CRF's Only Forums
Apr 18, 2017
Torque Specs 2006 CRF250x ? - CRF's Only Forums
Jul 1, 2009
Washers and Bolt Torque - CRF's Only Forums
Apr 9, 2017
More results from crfsonly.com

HONDA CRF250X

Honda http://owners.honda.com > 2005 > 2005_crf250x
side cover bolt (8). 6. Install the collar (7) and seat bolt (9) tighten the bolt to the specified torque: 20 lbf·ft (26 N·m, 2.7 kgf·m). Servicing Your Honda.
180 pages ..

Why do you need to replace the main bearing bolts? The torque spec is 85-91 ft lbs.

Rexton rx320 bolt torque specs for engine

Id ask here 2,,,, good guys...http://harleytalking.com/login.php?do=logout&logouthash=1313501436-eb7a83064e08c13f62cc323a7bbce4a8d217cd8d

When removing the pump unit with special tool (some auto-parts stores rent them), TURN CLOCKWISE TO LOOSEN the pump-unit, counter-clockwise to tighten. The Torq Specs for the pump-unit is: 73 Foot Pounds. There are stop tabs on the pump-unit that mate with the tab stoppers on the main water pump housing unit. I had to re-torq by visually viewing where the stop tabs where after the first torq, don't over-torq or you will bend the tab stoppers on the pump unit. ALSO...the water pump-unit front cover requires a new rubber gasket (you'll have to order it through GM or use RTV silicone under the old gasket, which has a grooved fitting inside the front cover). The Torq Specs for the front cover (5 bolts) and water neck cover (2 bolts) is: 89 Inch Pounds. Those small bolts tighten normal, clockwise.

Read more: http://wiki.answers.com/Q/How_do_you_replace_the_water_pump_on_a_1999_Oldsmobile_Aurora#ixzz1CeLdWsjN

Connecting Rods: First pass 15 lb ft. If you have an early first design final pass 60 degrees. Second design 75 degrees.

Main Crank Bolts: Inner bolts first pass 15 lb ft. A final pass additional 80 degrees. Tighten the outer bolts/studs 15 lb ft. Final pass 53 degrees.

Tighten the side cap bolts to 18 lb ft. Tighten the bolt on ones side of the bearing and then tighten the bolt on the opposite side of the same bearing cap.

Oil Pump Bolts: 18 lb ft.
Oil Pump Screen Nut: 18 lb ft
Oil Pump Screen Bolt: 106 lb in
Oil Level Indicator Tube Bolt: 18 lb ft
Oil Level Sensor: 115 lb in
Oil Pan Drain Plug: 18 lb ft
Oil Pan Bolt: 18 lb ft
Oil Pan (to front cover): 18 lb ft
Oil Pan (to rear cover): 106 lb in
Oil Pan Skid Plate Bolt: 15 lb ft

If you need more specs contact: [email protected]

Could not find specs for 2006 but this is the specs for 2005 5.6

Step 1: Bolts 9-12: 17 in. lbs. (1.9 Nm)

Step 2: Bolts 1-8: 17 in. lbs. (1.9 Nm)

Step 3: All bolts: 52 in. lbs. (5.9 Nm)

Step 4: All bolts: 92 in. lbs. (10 Nm)

Tighten front cover bolts to 8 ft. lbs. (11 Nm)

steering sec is going to be 83 lbft/ftlbs
and wheel bolts are going to be 95 lbft/ftlbs