Question about 2007 kawasaki ZZR1400 ABS

1 Answer

2007 Kawasaki ZZR1400 ABS 10 amp ignition fuse keeps blowing

The 10 amp ignition fuse keeps blowing after ten mins of riding @

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • kawasaki Master
  • 58,447 Answers

Hi, Anonymous before diagnosing your blown fuse issue, check the bottom of your seat, if its metal and comes in close proximity to the positive battery post you need to take the necessary steps to ensure there is no contact (electrical tape, thick rubber insulation, hammer a dent in the seat bottom etc.) You are going to need a wiring diagram from your service manual, a test light, an ohmmeter and plenty of extra fuses.
If you turn on your ignition switch and immediately blow a fuse you have a hard/dead short and is usually easy to find. With a test light connected to the hot side of the blown fuse holder start stabbing the wire/s that leads away from the fuse holder and towards the ignition switch, you test light will illuminate validating the short. When the test light fails to illuminate you have passed the short and need to back up until the test light illuminates, then look in the immediate area for the short.
If you driving down the road for 30 minutes or 15 miles and blow a fuse you have soft/flying short and may take some time and patience to find.
If the main fuse/circuit breaker constantly blows/trips while riding you probably have a faulty battery terminal connection. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. Any other fuses that constantly keep blowing while riding are usually caused by a loose or corroded ground wire in the circuit, which means you have to check, inspect, test each and everyone with an ohm meter set on a low ohm scale 100 ohms or less . Simply touch one lead to the ground source and the other lead to the battery negative terminal, a reading of zero indicates a clean solid ground. Any reading or infinity indicates a poor ground and needs to be repaired. Poor or weak grounds require excessive additional amperage to complete the circuit which in turn blows the small amperage fuse.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
ignition fuse keeps blowing
http://www.newninja.com/forums/f97/10a-ignition-fuse-problem-11497.html
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Posted on Jul 11, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 65 Answers

SOURCE: MAIN FUSE KEEPS BLOWING

there has to be something simple. check for broke/melted wires, wiggle test wires to make it blow fuse. how long does it take to blow fuse. does the fan go on.do you have to ride it to get it to blow?

Posted on May 04, 2009

  • 1 Answer

SOURCE: Ignition Fuse keeps blowing

From another forum,

"You've got an exposed hot wire somewhere in the power circuit that's grounding out and causing resistance in the wire. Not sure how to help on this one, electrical problems are damn near invisible, but I'd start looking for a burn mark or scorched insulation on any of the wiring leading up the relay, starter, or main fuze block in the tail."

Posted on Jun 11, 2009

bozcro
  • 867 Answers

SOURCE: 200o 1500 vulcan classic. My ignition fuse blows

you have a short somewhere in the ignition line. check all connections at coil, check for worn spark plug cables grounding on block.

Posted on Jul 26, 2009

SOURCE: keep on blowing tail light fuse

The wiring to the tail light needs to be checked its grounding somewhere.
Trace it from the rear to front.

Posted on Sep 19, 2009

nedkelly900
  • 345 Answers

SOURCE: 2000 ZX-9 blows the 10 amp ignition fuse everytime

there must be an exposed piece of wiring somewhere, touching to an earth, causing a short out, and the fuse to blow.?

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Kawasaki ZZR 1400 error code 51


Hi, Teresa for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
FI error code 51 ZX 14 com
Kawasaki Fault Codes
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual Kawasaki ZZR1400 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 21, 2018 | 2007 kawasaki ZZR 1400

1 Answer

2007 Kawasaki ZZR 1400 how to bleed the clutch


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Kawasaki ZZR1400 ABS Service Manual Clutch Fluid Bleeding The Clutch Line
06 11 ZX14 CLUTCH RESERVOIR CHANGE
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


May 08, 2014 | 2007 kawasaki ZZR 1400

1 Answer

2012 Kawasaki ZZR 1400 ABS fuse keeps blowing


Hi, Anonymous before diagnosing your blown fuse issue, check the bottom of your seat, if its metal and comes in close proximity to the positive battery post you need to take the necessary steps to ensure there is no contact (electrical tape, thick rubber insulation, hammer a dent in the seat bottom etc.) You are going to need a wiring diagram from your service manual, a test light, an ohmmeter and plenty of extra fuses.
If you turn on your ignition switch and immediately blow a fuse you have a hard/dead short and is usually easy to find. With a test light connected to the hot side of the blown fuse holder start stabbing the wire/s that leads away from the fuse holder and towards the ignition switch, you test light will illuminate validating the short. When the test light fails to illuminate you have passed the short and need to back up until the test light illuminates, then look in the immediate area for the short.
If you driving down the road for 30 minutes or 15 miles and blow a fuse you have soft/flying short and may take some time and patience to find.
If the main fuse/circuit breaker constantly blows/trips while riding you probably have a faulty battery terminal connection. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. Any other fuses that constantly keep blowing while riding are usually caused by a loose or corroded ground wire in the circuit, which means you have to check, inspect, test each and everyone with an ohm meter set on a low ohm scale 100 ohms or less . Simply touch one lead to the ground source and the other lead to the battery negative terminal, a reading of zero indicates a clean solid ground. Any number reading or infinity indicates a poor ground and needs to be repaired. Poor or weak grounds require excessive additional amperage to complete the circuit which in turn blows the small amperage fuse.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Help fuse blows bike dies bad CDI
ignition fuse keeps blowing
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 24, 2014 | 2011 kawasaki ZZR 1400

1 Answer

2007 Kawasaki ZZR1400 ABS size socket needed to remove the front axle nut


Hi, Trevor for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
front axle nut size KawiForums Kawasaki Motorcycle Forums
wheel removal Sportbikes net
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Sep 23, 2013 | 2007 kawasaki ZZR1400 ABS

1 Answer

2008 Kawasaki ZZR1400 ABS rear axle nut torque spec


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Gen 4 2011 2015 Front and Rear Axle Nut Torque Specs Kawasaki ZX 10R net
Axle torque spec ZX 14 com
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

May 18, 2013 | 2009 kawasaki ZZR1400 ABS

1 Answer

2009 Kawasaki ZZR1400 ABS error code 35


Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the blue links below. Good luck and have a wonderful day.
Kawasaki ZZR1400 ABS Service Manual Immobilizer Amplifier service Code 35...
Kawasaki Fault Codes
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Apr 11, 2013 | 2009 kawasaki ZZR1400 ABS

1 Answer

2007 Kawasaki ZZR 1400 engine oil capacity


Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the blue links below. Good luck and have a wonderful day.
How much oil goes in the 14 ZX Forums
Oil Change 2007 ZX 14
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Feb 09, 2013 | 2007 kawasaki ZZR 1400

1 Answer

2007 Kawasaki ZZR 1400 vibration at 3000 rpm


Hi, Anonymous and the usual suspects are:
1. Wheels and or tires worn or damaged.
2. Engine/transmission/vehicle not aligned properly.
3. Primary chain is badly worn or links too tight as a result of insufficient lubrication or misalignment.
4. Engine to transmission mounting bolts loose.
5. Upper engine mounting bracket loose.
6. Ignition timing incorrect due to a poorly tuned engine.
7. Internal engine problem flywheels have shifted.
8. Broken frame.
9. Stabilizer links worn or loose.
10. Rubber mounts loose or worn.
11. Rear fork pivot shaft nuts loose.
12. Front engine mounting bolts loose.
13. Worn out or broken universal joint on shaft drive models.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Vibration around 4000rpm KawiForums Kawasaki Motorcycle Forums
Vibration Help please ZX 14 com
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Jul 22, 2012 | 2007 kawasaki ZZR 1400

1 Answer

2009 Kawasaki ZZR1400 ABS battery location


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2009 Kawasaki ZZR1400 ABS battery location Google Search
Sportbike Battery Removal ZX14
Kawasaki ZZR1400 ABS Service Manual
OEM Parts for Kawasaki
Kawasaki ZZR1400 Owner Manual

Jan 04, 2012 | 2009 kawasaki ZZR1400 ABS

Not finding what you are looking for?
2007 kawasaki ZZR1400 ABS Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5944 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

ROB

Level 3 Expert

858 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...