2008 Honda XR 250 Tornado Logo

Related Topics:

Hannes Dreyer Posted on Oct 07, 2017

2009 Honda XR 250 Tornado turn signals not working

My indicators just stopped working on my 2009/2010 Honda XR 250 Tornado, cannot find a flicker unit on this bike. How does the indicator circuit work? Searched all over the bike and can not find a flicker unit, opened the switch and put power directly onto indicator circuit, indicator lights come on but do not flicker. Found a small unit with three points which have two diode signs facing each other in the fuse box, tested with a multimeter and found to be OK. does anyone know what else I can do?

5 Related Answers

Anonymous

  • 1139 Answers
  • Posted on Oct 01, 2007

SOURCE: No Satelite Signal Indication

The "front end" of your Receiver might be defective. Since your other unit is working then what might be happening is the signal to your unit might be dropping, to check this I would use a Satellite power meter, however if you do not have one you can use your other unit and connect it to the cable that your supposed defective unit is connected to. If the unit works then the problem is the supposed defective unit, if the unit does not work then this denotes a possible cable problem. Tell me if this works for you?

Ad

Anonymous

  • 67 Answers
  • Posted on Nov 30, 2007

SOURCE: Neff combi blown diode.

If the diode failed by opening, there may be no other damage. If the dioded failed by shorting, the alternating current may have damaged other components. Ohm it out. You can get diodes from digikey.com, mouser.com, or radio shack or any electronics or appliance supply. If the diode is charred and you can't get the part number, the oven rating can be used to select a replacement. Since the fuse was 10 amps, the diode should also handle at least 10 amps. If you can power the unit and read the voltage at the diode input this will give you the power (volts times amps). It's always worth trying as it's cheaper than replacing the unit.

andrewB2008

  • 1 Answer
  • Posted on Mar 06, 2008

SOURCE: power problem avic-N1

I removed the battery terminals and then reconnected and now my navigator doesn't work. When I take the faceplate off there is a flashing red light

Are there any internal fuses that I can check. External ones seem to be ok

Anonymous

  • 1 Answer
  • Posted on Jul 15, 2008

SOURCE: Where is the fuse box on 1991 Honda Accord LX (Automatic Tranny)???

On the driver's side, at your left foot is a compartment with a twist open, plastic lock; turn it and pull to reveal fuses

Anonymous

  • 20 Answers
  • Posted on Nov 28, 2008

SOURCE: NUMBER PLATE LIGHTS NOT WORKING

take the bulb back out and clean inside the bulb holder, there may be some corrosion or other debris in there

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

L have a Honda cbf 250 my indicators have stop working. next day l use the bike next day. when l turn the indicators on they work again switch off and turn them again they stop

Usually when electrical things bwork intermiittently, you have a loose wire somewhere - likely a ground wire for the lights. Check all wire connections for your lights and make sure they are tight and not corroded. If you have a loose or burned out bulb, the good signal light may come on but won't blink.Check your signal light switch too.

Don
0helpful
1answer

Overheating

Surprised that your mechanic didn't mention the spark plug. The wrong plug type is a major cause of overheating. Speak nicely to your local Honda dealer and ask his advice. You don't have to buy your plugs from him once you know which one you need visit your local motor factors the difference in cost will shock you.
0helpful
1answer

My indicators and speedo have stopped working

Bad connection, unclip connectors, clean, and spray with wd42.
5helpful
2answers

How to get the spark plug out of my honda xr200r

a very thin walled 18mm deep socket. I had to put the socket in a drill then use my grinder to get it to the right width. That was for my 85 xr350r. It took me a while to figure out.
0helpful
1answer

Need camshaft clearance for Ex and In

Exhaust: 0.12 +/- 0.02 mm (0.005 +/- 0.001 inch)
Inlet: 0.10 +/- 0.02 mm (0.004 +/- 0.001 inch)
Not finding what you are looking for?

228 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...