Question about 2004 Yamaha V Star Classic
My wife bought a 2004 v-star 650 classic, the free play at the lever is excessive and cannot be adjusted out, as near as I can tell the clutch is mechanical therefor should have a mechanical adjustment at the clutch itself. I have looked foe access to an adjuster on the side the cable, removing the shrouding to find nothing that looks like an access port. Where is said access? adjustment is fairly universal, so once found the job should be relarively easy. I have an electri-glide so perhaps I'm overlooking something becouse it is not blatently obvious.
The bike you are working on has a couple of way to adjust the clutch. Obviously the adjuster on the handlebars would be the first place but actually there is an adjustment on the other end of the cable that has a locking nut on it. You will need to loosen the nut that locks the cable and there should be another nut on the other side of the cable that you can tighten. As you tighten the nut it will take the free play out of the cable.
There is another adjustment on the inside of the clutch cover, it is on the clutch hub. The adjustment for this would be done by removing the clutch cover to access the clutch hub. On the outside of the hub there is an 12mm nut locking down a 6mm adjusting screw, the screw is adcually the first source of adjustment on initial assembly.
Let me give you the breakdown of how this works, your clutch mechanism has the hub adjustment, a ball, and a push rod that goes through the primary output shaft of the transmission. Then it goes to the actuating arm where your cable connects. The reason I'm telling you this is because often the ball in between the hub adjuster screw and the clutch push rod becomes welded to the push rod or it will actually start to come apart. When this happens your clutch adjustment goes away and you have no adjustment available through the cable or the clutch lever. Should this be your case I would recommend you take the clutch cover off, (be sure to drain the oil first), remove the six 10mm nuts securing the clutch hub, (this also holds the clutch springs in place), then you will have access to the push rod and the ball. You may have to tilt the bike over on the right side to get the push rod and ball to come out.
When you go to reassemble the clutch make sure all the adjusters are loose so you can adjust the clutch in the following sequence:
Good Luck! This is a DIY job, you wont need to take the bike to the shop if you are able to do any routine maintenance. Should you have to remove the clutch cover you will need to replace the right side, (clutch cover), engine gasket. If you take it apart I would recommend replacing the ball if it has any signs or wear, it will be blotted, this is a very cheap item that can cause much grief.
Let me know if you need any further assistance.
Posted on Jan 02, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Sep 13, 2013 | 2004 Yamaha V Star Classic
May 10, 2013 | 2008 Yamaha V Star 1100 Classic
Mar 04, 2013 | 2004 Yamaha V Star Classic
Feb 21, 2013 | 2004 Yamaha V Star Classic
Aug 30, 2011 | 2004 Yamaha V Star Classic
Feb 28, 2011 | 2004 Yamaha V Star Classic
Feb 14, 2011 | 2004 Yamaha V Star Classic
May 08, 2010 | 2006 Yamaha V Star Classic
Apr 16, 2010 | 2004 Yamaha V Star Classic
Jan 19, 2009 | 2004 Yamaha V Star Classic
Oct 22, 2019 | Comet Motorcycles
Oct 22, 2019 | Motorcycles
7,671 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: