Question about 2001 kawasaki VN 1500 Vulcan Classic

1 Answer

Feul injection I was riding normal and the motor started running like on 1 cyl when i got home pulled air cleaners had feul overload in font cyl , feul comming out exaust and throttle body opened butterfly and front tract full of feul

Posted by on

  • 1 more comment 
  • wes boroski Jun 22, 2012

    The bike is a 2001 vulcan classic with cobra exaust

  • wes boroski Jun 22, 2012

    any help would be appreciated i am new to this site and dont know how it works

  • wes boroski Jun 23, 2012

    never mind i did a compression test and #1 cyl is bad have to replace piston thanks for help

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 19 Answers

SOUNDS AS IF INJECTERS NEED CLEANING.
FIRST STAGE LOAD YOUR FUEL TANK UP WITH SOME INJECTER CLEANER AVAILABLE FROM ANY MOTOR *** SHOP AND RUN THE ENGINE. IF IT'S AS BAD AS YOU SAY YOU MAY NEED TO USE DOUBLE OR TRIPLE STRENGTH. IF THAT DOES NOT WORK TRY REMOVING INJECTERS AND SOAK THEM IN THE SAME NEAT FLUID. ALSO HAVE YOU CHECKED THE ELECTRICS TO THE INJECTERS AND ALSO THAT THE PLUGS ARE CLEAN AND SPARK UNDER COMPRESSION.

Posted on Jun 23, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: will start and run but needs loads more choke than

You need to clean your carbs. Something is gummed up inside. Most likely pilot jet, but need to clean and synchronize them.

Posted on Mar 07, 2009

  • 15 Answers

SOURCE: bike starts fine, idles fine low end fine, mid and

is your gas tank clean ? ever drain the carb? should every season. check to see if you have correct spark plug and gap. check fuel line for crimp.

Posted on Oct 11, 2009

jmurtagh617
  • 11 Answers

SOURCE: 2007 kawasaki zx6r ninja cranks but no start, not

check ground

Posted on Feb 24, 2010

  • 1 Answer

SOURCE: wont start by kick start but will by pull start

it could be the gaskets around your carb are bad and leaking air if so its thinning your gas fumes with more air then what is needed inside your combustion chamber witch is causing your engine to stop running like that. best of luck

Posted on Apr 20, 2010

  • 27 Answers

SOURCE: 99 kawasaki kx 125 2-stroke wont start or stay

I would check the compression of the piston, the rings could be stuck and not have good compression. It should show 120 psi or more. Also can pull off the exhaust and look in the exhaust port to see the rings, piston, and cylinder walls. If the motor has a power valve make sure that is not gummed up or stuck. Mark C

Posted on Jun 02, 2011

Testimonial: "It was good advise, I still have not fixed the problem, but we are working on a solution as we speak. trying to narrow it down and we are close"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 99 bmw 323i.i ran it hot and got prob fixed and now the eml and a triangle with circle around it comes on dash and car has no power.feels like it has a rev limiter.wats wrong with my car


have throttle body checked also the MDK throttle motor,
make sure that the dealer has followed service bulletin 12 07 99 for procedure to replace the MDK throttle motor
also have them check for codes,here are some codes,
it could be an expensive job,have them check everything,it is most likely the throttle motor,,throttle body is 600 if they switch it,dont let them do it without checking throttle motor,
codes,
MS41, MS42 and MS43 engine DME bmw codes...
• 1 Ignition coil Cyl 2
• 2 Ignition coil Cyl 4
• 3 Ignition coil Cyl 6
• 5 Fuel injector Cyl 2
• 6 Fuel injector Cyl 1
• 8 Air Flow Meter (HFM)
• 10 Coolant Temperature Sensor
• 11 Tank Pressure Sensor (EVAP System) or Radiator Outlet Temp (MS43)
• 12 TPS or Plausibility - Maximum Coolant Temp (MS43)
• 13 Plausibility- Radiator Outlet Temp
• 14 Intake Air Temperature Sensor
• 15 Plausibility - Cut Out Time
• 16 AirCon Compressor - PWM Signal or Plausibility Intake Air Temp (MS43)
• 17 Plausibility - Engine Coolant Temp
• 18 EWS Signal or Camshaft Sensor (MS43)
• 19 Activation VANOS Inlet Valve or Exhaust Valve (MS43)
• 20 "CHECK ENGINE" Light Failure
• 21 VANOS -Electrical Fault or Activation VANOS Inlet Valve (MS43)
• 22 Fuel Injector Cyl 3
• 23 Fuel Injector Cyl 6
• 24 Fuel Injector Cyl 4
• 25 Lambda Sensor Heater -Bank 1
• 27 Idle Control Valve - Malfunction
• 29 Ignition Coil Cyl 1
• 30 Ignition Coil Cyl 3
• 31 Ignition Coil Cyl 5
• 33 Fuel Injector Cyl 5
• 35 Aux. Air Injection System Relay
• 36 DME Main Relay
• 37 DME Main Relay : Delay
• 38 Clutch Switch -Plausibility
• 39 Brake Light Switch or Brake Light Test Switch
• 40 Brake Light Switch or Pedal Value Signal
• 42 Multi Function Steering Wheel- Plausibility
• 43 Multi Function Steering Wheel: Button
• 45 Multi Function Steering Wheel: Port
• 47 Temp Sensor -Downstream of Pre-Cat or Torque Limitation Level 1 (MS43)
• 48 DME Control Unit -Self Test 1
• 49 DME Control Unit or Torque Monitoring Level 2 (MS43)
• 50 EVAP Control Valve or Response Monitoring Level 2 (MS43)
• 51 Shut-off Valve -Charcoal Filter or Request Control Unit Reset (MS43)
• 52 Solenoid Valve -Exhaust Flap
• 53 Idle Speed Actuator
• 55 Lambda Sensor Heater -Bank 2
• 56 Ignition Current Feedback Resistor - Open Circuit
• 57 Knock sensor -Bank 1
• 58 DME Control Unit -Self Test 2
• 59 Knock Sensor -Bank 2
• 61 Lambda Sensor Heater -Bank 2 Post Cat
• 62 Aux. Air Injection System -Switching Valve
• 63 DME Control Unit or Ambient Temp Signal via CAN (MS43)
• 64 Plausibility - Ambient Temperature
• 65 Camshaft Position Sensor (Inlet MS43)
• 66 DME Control Unit
• 67 DME Control Unit
• 68 Tank Venting Valve
• 69 Fuel Pump Relay
• 70 DME Control Unit
• 71 DME Control Unit
• 72 DME Control Unit
• 74 AirCon Compressor Relay
• 75 Lambda Sensor Voltage -Bank 1
• 76 Lambda Sensor Voltage -Bank 2
• 77 Lambda Sensor Voltage -Bank 1 Post Cat
• 78 Lambda Sensor Voltage -Bank 2 Post Cat
• 79 Lambda Sensor Heater -Bank 1 Post Cat
• 80 ABS/ASC interface
• 81 MSR Signal -Active too Long
• 82 ABS/ASC Interface -Advance Adjustment
• 83 Crankshaft Sensor
• 90 Exhaust Temperature Pre Cat Conv - Bank 1
• 91 Exhaust Temperature Pre Cat Conv - Bank 2
• 92 Exhaust Temperature Post Cat Conv -Bank 1
• 93 Exhaust Temperature Post Cat Conv -Bank 2
• 94 Auxiliary Air -Air Mass Flow Sensor
• 95 Auxiliary Air Valve or Auxiliary Air Hose Blocked
• 96 Auxiliary Air Pump - Function
• 97 Auxiliary Air -Flow Rate too Low
• 98 Auxiliary Air -Flow Rate too High
• 99 Auxiliary Air Valve Jammed Open
• 100 DME Control Unit -Self-Test Failed
• 103 VANOS Error -Inlet Camshaft
• 104 VANOS Error -Exhaust Camshaft
• 105 VANOS Error -Position Inlet Camshaft
• 106 VANOS Error -Position Exhaust Camshaft
• 109 Throttle Valve Plausibility
• 110 Pedal Sensor Value Potentiometer 1
• 111 Pedal Sensor Value Potentiometer 2
• 112 TPS Potentiometer 1
• 113 TPS Potentiometer 2
• 114 Throttle Valve Final Stage
• 115 Reference Voltage -Voltage Regulator 1 or Throttle Pedal Adaptation (MS43)
• 116 Reference Voltage -Voltage Regulator 2
• 117 Plausibility -Pedal Position Sensor 1/2
• 118 Plausibility -TPS 1/2 or TPS1/Airflow Plausibility (MS43)
• 119 Throttle Valve Sensor -Mechanical Error or TPS2/Airflow Plausibility (MS43)
• 120 Plausibility Pedal Sensor or TPS
• 122 Engine Oil Temperature
• 123 Map Cooling Thermostat Control
• 124 Activation DISA Solenoid
• 125 Activation Electric Fan
• 126 Activation Tank Leak Pump Solenoid
• 127 Activation Pump Solenoid
• 128 DME/EWS Communication
• 129 CAN Signal SMG 1
• 130 CAN Signal ASC -Timeout
• 131 CAN Signal Instrument Cluster -Timeout
• 132 CAN Signal Instrument Cluster -Timeout
• 133 CAN Signal ASC -Timeout
• 134 SMG Intervention -Plausibility
• 135 Throttle Valve Re-Adaptation Required
• 136 Throttle Valve -Spring Test and Limp-home Position Failed
• 137 CAN Signal -Steering Angle Sensor
• 139 CAN Signal -Tank Level Sensor
• 140 Tank Leak Pump Solenoid - Reed Switch Open or Output Stage (MS43)
• 141 Tank Leak Pump Solenoid - Reed Switch Stuck Closed or Tank Level Sensor (MS43)
• 142 Tank Leak Pump Solenoid - Reed Switch Stuck Open or DMTL Module (MS43)
• 143 Tank Ventilation or Tank Leakage (MS43)
• 144 Fuel System - Large Leak Recognised
• 145 Fuel System - Small Leak Recognised
• 146 EVAP System Leak Detected (Small Leak) or Pedal Sensor Supply Voltage Pot 1 (MS43)
• 147 Pedal Position Sensor Potentiometer Supply Channel 1 (Pot 2 MS43)
• 149 Air Flow Sensor or Pedal Value Sensor Mismatch
• 150 Lambda Post Cat Bank 1 Max Limit
• 151 Lambda Post Cat Bank 2 Max Limit
• 152 Lambda Post Cat Bank 1 Min Limit
• 153 Lambda Pre Cat Bank 2 Max Limit
• 154 Lambda Pre Cat Bank 2 Min Limit
• 155 Lambda Pre Cat Bank 2 No Signal
• 156 Lambda Pre Cat Bank 1 No Signal
• 157 Lambda Post Cat Bank 1 Min Limit
• 159 Lambda Post Cat Bank 2 Max Limit
• 160 Lambda Post Cat Bank 2 (MS41) or Throttle Valve Stuck
• 161 Throttle Valve - Stuck
• 162 Throttle Valve -Control Deviation
• 168 Pedal Position Sensor Pot Supply 1 or MAP Cooling Thermostat Jammed (MS43)
• 169 Throttle Valve Output Stage Cut off after Fault
• 170 DME Control Unit -Self Test Failed
• 171 Plausibility - Throttle Valve
• 172 Pedal Sensor Potentiometer 1/2 Short Circuit
• 173 TPS Potentiometer 1/2 Short Circuit
• 174 Throttle Valve Potentiometer 1/2 Adaptation
• 175 Pedal Sensor 1 Adaptation
• 176 Pedal Sensor 2 Adaptation
• 186 Voltage Post Cat Bank 1
• 187 Voltage Post Cat Bank 2
• 188 Voltage Pre Cat Bank 1
• 189 Voltage Pre Cat Bank 2
• 190 EVAP -Reed Switch Open or Voltage Post Cat Bank 1 (MS43)
• 191 EVAP -Reed Switch Closed or Voltage Post Cat Bank 2 (MS43)
• 192 EVAP -Reed Switch Open
• 193 EVAP -Check Hoses
• 194 EVAP -Large Leak Detected
• 195 EVAP -Small Leak Detected
• 196 EVAP -Electrical Valve from LDP Pump or Barometric Pressure Sensor (MS43)
• 197 EVAP -Barometric Pressure Sensor
• 198 Cat Efficiency during Start -Bank 1
• 199 Cat Efficiency during Start -Bank 2
• 200 Lambda Regulation Bank 1 Pre Cat
• 201 Lambda Regulation Bank 2 Pre Cat
• 202 Lambda Regulation Bank 1 Post Cat
• 203 Lambda Regulation Bank 2 Post cat
• 204 Idle Control System -Idle speed not plausible
• 208 EWS -RPM Signal Error
• 209 EWS -Message Error
• 210 Ignition Feedback Resistor (ZSR)
• 211 Idle Speed Actuator -Mechanical
• 212 VANOS Bank 1 -Mechanical
• 214 Vehicle Speed Signal (VSS)
• 215 Lambda Sensor Bank 1 or ASC/MSR/EML -Interface not plausible
• 216 Lambda Sensor Bank 2 or EGS Position Signal
• 217 CAN bus error -EGS Signal not present
• 218 CAN module -Warning
• 219 CAN module -CAN Offline
• 220 Lambda Voltage Range Bank 1 Sensor 1
• 221 Lambda Voltage Range Bank 2 Sensor 1
• 222 Low Coolant Temperature or Lambda Sensor Control (MS43)
• 223 Lambda Sensor Switching Bank 1 Sensor 2
• 224 Lambda Sensor Switching Bank 2 Sensor 2
• 225 Cat Efficiency Bank 1
• 226 Cat Efficiency Bank 2
• 227 Mixture Deviation Bank 1
• 228 Mixture Deviation Bank 2
• 229 Lambda Sensor Switching Bank 1
• 230 Lambda Sensor Switching Bank 2
• 231 Lambda Sensor Switching Bank 1 Pre Cat
• 232 Lambda Sensor Switching Bank 2 Pre Cat
• 233 Catalytic Converter Overall Efficiency Bank 1
• 234 Catalytic Converter Overall Efficiency Bank 2
• 235 Lambda Heater Bank 1 Post Cat or Pre Cat Signal (MS43)
• 236 Lambda Heater Bank 2 Post Cat or Pre Cat Signal (MS43)
• 238 Misfire Cyl 1
• 239 Misfire Cyl 2
• 240 Misfire Cyl 3
• 241 Misfire Cyl 4
• 242 Misfire Cyl 5
• 243 Misfire Cyl 6
• 244 Crankshaft Interval Timing
• 245 Aux Air Injection System Bank 1
• 246 Aux Air Injection System Bank 2
• 247 Aux Air Injection System -Incorrect Flow Detected
• 248 Pre Cat Converter Efficiency -Bank 1
• 249 Pre Cat Converter Efficiency -Bank 2
• 250 Tank Venting Valve -Function
• 251 Tank Ventilation Diagnosis Error
• 252 Tank Ventilation System Vacuum
• 253 Activated Charcoal Filter Shut-off Valve Stuck Shut
• 254 Tank Ventilation System -Large Air Leak
• 255 Tank Ventilation System -Valve Stuck Open

Apr 03, 2015 | 1999 BMW 323i

1 Answer

Toyota grandhiace diesel engine 3.0 1 kz start heavy feul consumption.


check for fuel leak at the pump. pull and fit new tips to the injectors. Have the injection timing checked by an accredited diesel shop ( same one that is replacing the injector tips)

Apr 11, 2014 | 1995 Toyota Hi-Ace

1 Answer

Hi I have an Audi 2.6 1998 cabriolet, in the morning went to work with it an everthing was fine, started it that afternoon after work to go home, (this was about 2 months ago and still trying to locate...


It sounds like the timing is off or a bad timing belt/chain.The dieseling effect is usually due to excessive carbon buildup inside the combustion chamber.Try a fuel injection service to see if that solves the problem of the pre-ignition.

Oct 02, 2010 | 1996 Audi A4

1 Answer

99 f250 7.3......has been running rough mid throttle, yesterday on the highway it died but started back up before i could get pulled over,today it shut off and stated it back up and made it home...i have...


spray some carb cleaner down the breather pipe the carb could be clogged up so it is not opening properly and choking the engine or flush out your feul they may be dirty and your not getting enough fuel through when you need it or your air intake senser might need changing cus if your air/fuel mix is wrong your engine will stall

Mar 22, 2010 | 1999 Ford F250 Regular Cab

1 Answer

Engine starts well but only runs on idle,but won't rev up


You need to perform some maintenance on that rider.
First ensure that you are using fresh gasoline.
Then pull that air cleaner off and clean it. Normally if its a sponge filter clean it in some solvent than squeeze it out really good.
After wards get a little cup of motor oil and soak it in that and squeeze that out. If it cant be cleaned than replace it.
You are choking out your motor with that dirty air cleaner.
If after you get it all cleaned up and and ensure your gas is fresh and it still does it then it needs to go into the shop for a major repair I cant walk you through on here.

Mar 08, 2010 | Garden

1 Answer

I have a 1993 dyna harley davidson with a1340 ss motor. i will ride for a little and the motor will miss fire .pull over two the side and i can remove the coil wire to rear cyls no spark replaced coil...


ok buddy are you running the correct heat range plug as when wrong pluges get hot they foul and when the cool the come back to life so try that 1st also what colour are the plugs when you pull them out get back to me

Sep 15, 2009 | 2000 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

2006 yamaha straoliner, engine code 37 comes up


Displayed Fault Codes For The ‘Liners
  • 12 - Crankshaft Position Sensor <<Dead Engine>>
  • 13 - Cyl #1 Intake Air Pressure sensor (open or shorted)
  • 14 - Cyl #1 Intake Air Pressure Sensor (hose system) - Clogged or detached
  • 15 - Throttle Position Sensor (open or shorted)
  • 17 - EXUP Servo Motor Ckt. (open or shorted)
  • 18 - EXUP Motor Locked Up – Frozen
  • 19 - Blue/Black ECU wire broken or disconnected <<Dead Engine>>
  • 22 - Air Temp Sensor (in headlight) (open or shorted)
  • 24 - O2 Sensor – No Normal Signal Received
  • 25 - Cyl #2 Intake Air Pressure Sensor (open or shorted)
  • 26 - Cyl #2 Intake Air Pressure Sensor (hose system) - Clogged or detached
  • 28 - Engine Temp. Sensor (open or shorted)
  • 30 - Lean Angle Sensor Latched Up (Bike Laid Down) <<Dead Engine>>
  • 33 - Cyl #1 L. or R. Faulty Ignition Coil << May Run >>
  • 34 - Cyl #2 L. or R. Faulty Ignition Coil << May Run >>
  • 35 - Cyl #1 L. or R. Faulty Ignition coil << May Run >>
  • 36 - Cyl #2 L. or R. Faulty Ignition Coil << May Run >>
  • 37 - ESC Valve Stuck Open (Engine Speed Control / High Idle Speed)
  • 41 - Lean Angle Sensor (open or shorted) <<Dead Engine>>
  • 42 - Speed Sensor – No Normal Signals Received OR Neutral Switch (open or shorted)
  • 43 - Fuel System Voltage (ECU Unable to Monitor Batt. Voltage)
  • 44 - Error In Writing Amount Of CO Adjustment To EEPROM
  • 46 - Voltage To F.I. System Not Normal
  • 50 - ECU Internal Failure – Memory Check <<Dead Engine>>
  • 70 - Engine Idling Stop – After 20 Minutes Of Idling

Apr 08, 2009 | 2006 Yamaha Stratoliner S

2 Answers

I have a '99 Camry w/109,000 miles which keep cutting out some-


  1. CHECK FOR VACUUM LEAKS
  2. Throttle body or egr valve carbon build up
  3. Tps Bad? any Codes ?
  4. CARB/INJECTION Cleaner Spray into intake While at Approx 3500 RPM
  5. STP Feul Injecttion cleaner for TANK Pore it in W/ 1/2 tank run in on inerstate at 70-80 if u can get the COBWEBS OUT so to speak

Jan 13, 2009 | 1999 Toyota Camry

Not finding what you are looking for?
2001 kawasaki VN 1500 Vulcan Classic Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5873 Answers

Marvin
Marvin

Level 3 Expert

84966 Answers

richard libby

Level 2 Expert

208 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...