Remove headlight bezel 2006 stratoliner - 2006 Yamaha Stratoliner S

LIGHTING Headlights REMOVAL & INSTALLATION Cherokee, Wagoneer and Comanche Models Fig. 1: Remove the top corner headlight bezel mounting screw
Fig. 2: To access the turn signal bulb or headlight bezel mounting screws, remove the 2 turn signal housing retaining screws
Fig. 3: After removing the turn signal housing from the headlight bezel, remove the 2 bezel mounting screws . . .
Fig. 4: . . . then carefully pull the headlight bezel away from the headlight assembly
Fig. 5: Remove the 4 headlight assembly retaining ring screws . . .
Fig. 6: . . . then pull the retaining ring off of the headlight assembly
Fig. 7: Pull the headlight assembly away from the vehicle just far enough to disengage the electrical connector from behind the headlight

1. Remove the headlamp bezel and retaining ring attaching screws. Remove the bezel and retaining ring.
2. Pull the headlight out, disconnect the wire harness and remove the headlight from the vehicle.
3. Install the headlight in the reverse order of removal.

Grand Cherokee and Grand Wagoneer Models

1. Open the hood, reach into the engine compartment and locate the lock ring supporting the bulb assembly.
2. Rotate the lock ring 1?8 turn counterclockwise and pull the bulb straight out from the housing. To install:
   
3. Install a new bulb and position the bulb assembly in the lamp housing.
4. Rotate the lock ring 1?8 turn clockwise to secure.

----
The Grand Cherokee will have an assembly that is fastened with bolts and screws to the body.
Get the new assembly and compare to the old one to see where to unfasten the bolts and other fasteners to aid in removing quickly.

There should be screws holding it in from the top. You must remove the seat first.

REMOVAL & INSTALLATION 1984–88 Vehicles

1. Open the hood, then turn the headlights on.
2. Detach the headlight motor wire on the outer side of the headlight.
3. Turn the headlights off (the disconnected light should stay open).
4. Unfasten the 4 screws at the bezel. There are 2 at the front and 2 at the sides. Fig. 1: With the hood in the raised position, unfasten the Torx® screws from the outer side of the headlight bezel/trim piece
   Fig. 2: You must then remove the screws from the inner side of the bezel/trim piece
   
   
5. Remove the bezel. Fig. 3: Remove the first of the top bezel/retaining ring screws . . .
   Fig. 4: . . . then remove the remaining Torx® screw
   Fig. 5: Lift the bezel/trim piece away from the headlight assembly
   
   
6. Remove the retaining spring by carefully using a hooked end tool, such as a cotter pin removal tool to move it to the side.
7. Remove the headlight from the aiming pins by rotating the headlight toward the center of the car.
8. Unfasten the 4 retaining ring screws, then remove the ring. Fig. 6: With the hood closed, you can see the 4 headlight retaining ring screws (1) and 2 aiming screws (2)
   Fig. 7: Remove ONLY the 4 retaining ring screws, do NOT touch the aiming screws
   
   
9. Remove the headlight pump from the mounting bracket, unplugging the socket as you pull it away. Fig. 8: Remove the headlight away from the mounting bracket, unplugging the socket as you pull it away
   To install:
   
10. Install the headlight bulb, making sure it is plugged in properly.
11. Position the retaining ring and secure with the 4 screws.
12. Position the headlight into the aiming pins. Move the retaining spring back into place.
13. Install the bezel and secure with the retainers.
14. Turn the headlights on, then connect the headlight motor wire.
15. Turn the headlights off. Both should lower.
16. Close the hood. Check the aim of the headlights, and adjust if necessary.

1989–96 Vehicles

1. Open the hood.
2. Open the headlight door halfway. This can be done either by turning the headlight switch on, then back to the parking lamp on position, or by the manual headlamp control knob (which is located on the inboard side of the headlight door). NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
   
3. Remove the screws from the front of the headlight bezel. NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
   
4. Remove the Phillips head screws from each side of the headlight bezel.
5. Remove the bezel by pulling it straight out from the engine side of the hood. Fig. 9: View of the headlight bezel mounting
   
   
6. Unfasten the screws from the headlight retaining ring.
7. Remove the headlamp from the assembly, unplugging the electrical connector as you are pulling it away. Fig. 10: Exploded view of the headlight assembly
   Fig. 11: Location of the headlight mounting and aiming screws
   To install:
   
8. Attach the headlight electrical connector.
9. Position the retaining ring and install the screws securing the ring to the headlight.
10. Position the bezel in place on the headlight assembly.
11. Install the screws on each side of the bezel and tighten to 51 inch lbs. (5.8 Nm).
12. Install the screws on the front of the bezel and tighten to 17 inch lbs. (1.9 Nm).
13. Cycle the headlamps, then close the hood. Check the headlight aim, and adjust if necessary.

Sealed Beam Type

1. Disconnect the negative battery cable.
   
2. Unfasten the headlight bezel attaching screws, then remove the bezel.
   

Remove the headlight bezel

To avoid turning the vertical or horizontal aiming screws, refer to the illustration before removing the headlight retainer.

1. Unfasten the headlight retainer attaching screws, then remove the retainer.
   

Remove the headlight trim screws then...


... pull the trim off while holding the bulb

4. Pull the headlight out, then carefully detach the electrical connector.


Pull the bulb out far enough to disconnect the wiring


To install:

1. Attach the electrical connector to the new headlamp.
   
2. Place the headlamp into the socket.
   
3. Install the retainer, then tighten the attaching screws.
   
4. Connect the negative battery cable, then turn the headlight switch on, to be sure the headlights are operating.
   
5. Install the headlight bezel and secure using the attaching screws.
   

There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.

To Replace:

• Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
• Remove the retaining ring screws from one or both lights.
• Remove the retaining rings.
• Remove the light from the housing. Disconnect the wiring connector from the back of the light.
• Push the wiring connector onto the prongs at the rear of the new light.
• Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
• Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
• Check the aim of the headlight and adjust it, if necessary.
• Install the headlight bezel. Secure it with the retaining screws.
• Connect the turn signal lamp wiring (if it was disconnected).

Hope this helps!

hi..Should be a Halogen bulb High-low beam combo maybe.
As you are looking down at the back of the headlight assembly
gently push down on the clip that holds the wiring harness to the
bulb. Now rotate the bulb counter clock wise (left) and then remove
it. Reverse process to install.
check it out..
thank u..
rate me..

You have to take off the bumper to get access to head light